The Triumph Dolomite Club - Discussion Forum http://forum.triumphdolomite.co.uk/ |
|
Operation Orange - 1980 Sprint restoration http://forum.triumphdolomite.co.uk/viewtopic.php?t=17826 |
Page 23 of 24 |
Author: | Mad Mart [ Fri Dec 01, 2017 4:23 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
Manifold looks sexy! I've had the studs made shorter now Mark. Bit late for your build I know. |
Author: | James467 [ Sat Dec 02, 2017 10:16 am ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
That manifold looks like you painted it! Told you it would come up well, looks almost as good as mine!! |
Author: | lazeruspete [ Sat Dec 02, 2017 12:06 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
shiny |
Author: | Jon Tilson [ Sun Dec 03, 2017 3:20 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
....after multiple bitches about the stud length its getting sorted... Better late than never. Jonners |
Author: | SprintMWU773V [ Tue Dec 12, 2017 10:07 am ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
On assembling the head as suggested by Jeroen that the inlet valves in particular do sit too high in the head. I thought I might have been able to work with what I had but even using the thinnest shims I could not get adequate valve clearance. This is very annoying and has led some some heated discussion between myself and the machine shop who insist there is not a problem. I should add I'm not going to go into the details of my experience on a public forum. I suspect the seats have been cut before, the additional cut probably means too much meat has come off them. There is no alternative but to fit new seats. I could probably work with the exhausts which will require shims in the mid 80's but I'm tempted to just have new seats fitted throughout and be done with it. This additional work will also cause my chamber volumes to change so further work may be necessary not to mention the additional handling risks damaging the ready skimmed mating face. I have other people to speak to about valve seats and fitting but the question is are they easily available? I waited a long time for the head to come back to me, I'm not really in the mood for being messed around. I'll now have to strip the head back to bare again and hope for better luck the second time around. It's just annoying that until you start to shim the thing up you cannot be 100% sure. |
Author: | James467 [ Tue Dec 12, 2017 10:14 am ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
They should be standard fitting Mark. Roe engineering haven't had a problem getting any for the two heads that I have had done. |
Author: | SprintMWU773V [ Tue Dec 12, 2017 2:00 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
Quote:
They should be standard fitting Mark. Roe engineering haven't had a problem getting any for the two heads that I have had done.
That's good to know. If I still lived down your way I'd probably take it to Roe but I think I may have found someone local to me who I'd um'd and ah'd taking it to in the first place. Hopefully it'll be a straightforward job and can be back with me again soon. |
Author: | James467 [ Tue Dec 12, 2017 2:30 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
Well if there are any problems then I'm sure we could meet somewhere and I can drop it in to them. Need to remove DTRs head and get it over to them |
Author: | soe8m [ Tue Dec 12, 2017 6:03 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
That's bad news. I can't count on two hands anymore the times I had to take off a head because of a valveseat dangling around a valve stem. It does happen often and is only caused by a machineshop that can't do a proper job or doesn't care to do a proper job. There's going to be a chamber machined in the head and the insert, just a ring, is pressed in. The slightes wrong machining can cause the seats fall out the head. Heating the head and freezing the inserts is the way to press them in. Also the situation of determining the machining sizes at those temp differences if not available by the insert manufacturer. After fitting the insert the seat is machined in the desired shape. Have the work done at a shop with good reviews or recommended by others. Not a shop what just happened to be around the corner where you don't know the quality of the work of. Jeroen |
Author: | Carledo [ Tue Dec 12, 2017 9:32 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
Not TOO far from you Mark, I can thoroughly recommend Head Technique in St Georges Telford (01952 610770) who have been doing all my head work for the past 30 years, not just Triumph but everything else too. Sensible prices as well! I have no connection with the company, other than as a satisfied customer! Steve |
Author: | tony g [ Tue Dec 12, 2017 10:01 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
Mark, the other alternative is to fit a reprofiled cam like Kent supply. Smaller base circle so more valve clearance. i did it with mine after a valve job and it runs lovely. Idles well and pulls like a train. Just worth a look unless it has to be stock in your case. Tony Quote:
On assembling the head as suggested by Jeroen that the inlet valves in particular do sit too high in the head. I thought I might have been able to work with what I had but even using the thinnest shims I could not get adequate valve clearance. This is very annoying and has led some some heated discussion between myself and the machine shop who insist there is not a problem. I should add I'm not going to go into the details of my experience on a public forum. I suspect the seats have been cut before, the additional cut probably means too much meat has come off them. There is no alternative but to fit new seats. I could probably work with the exhausts which will require shims in the mid 80's but I'm tempted to just have new seats fitted throughout and be done with it. This additional work will also cause my chamber volumes to change so further work may be necessary not to mention the additional handling risks damaging the ready skimmed mating face.
I have other people to speak to about valve seats and fitting but the question is are they easily available? I waited a long time for the head to come back to me, I'm not really in the mood for being messed around. I'll now have to strip the head back to bare again and hope for better luck the second time around. It's just annoying that until you start to shim the thing up you cannot be 100% sure. |
Author: | soe8m [ Tue Dec 12, 2017 10:47 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
Quote:
Mark, the other alternative is to fit a reprofiled cam like Kent supply. Smaller base circle so more valve clearance. i did it with mine after a valve job and it runs lovely. Idles well and pulls like a train. Just worth a look unless it has to be stock in your case.
The seats are wrong and the valves are too deep. The opening and flow are also less than when the seats and valves are fitted the way they should. It has nothing to do with solving the play issue. There are lot's of folks who grind some of the top of the valve stem to have more play. The issue here is that the seats are wrong and the valves are too deep and that is confirmed by having no play.Tony Quote:
On assembling the head as suggested by Jeroen that the inlet valves in particular do sit too high in the head. I thought I might have been able to work with what I had but even using the thinnest shims I could not get adequate valve clearance. This is very annoying and has led some some heated discussion between myself and the machine shop who insist there is not a problem. I should add I'm not going to go into the details of my experience on a public forum. I suspect the seats have been cut before, the additional cut probably means too much meat has come off them. There is no alternative but to fit new seats. I could probably work with the exhausts which will require shims in the mid 80's but I'm tempted to just have new seats fitted throughout and be done with it. This additional work will also cause my chamber volumes to change so further work may be necessary not to mention the additional handling risks damaging the ready skimmed mating face.
I have other people to speak to about valve seats and fitting but the question is are they easily available? I waited a long time for the head to come back to me, I'm not really in the mood for being messed around. I'll now have to strip the head back to bare again and hope for better luck the second time around. It's just annoying that until you start to shim the thing up you cannot be 100% sure. Jeroen |
Author: | PaulB [ Wed Dec 13, 2017 7:04 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
Why not contact Rob McGregor or Ken Clark for recommendations. They both race Sprints and would have loads of experience with heads. |
Author: | Jon Tilson [ Wed Jan 10, 2018 12:46 pm ] |
Post subject: | Re: Operation Orange - 1980 Sprint restoration |
I would fit the head and get the timing sorted on the chain before fitting the ffront cover. I'd also check the spring tension on the rear crank oil seal unless you are confident of its provenance. I think its easier to fit the whole engine with pump and manifolds etcall in place than refit it peacemeal to a bare block in the bay myself. Jonners |
Page 23 of 24 | All times are UTC+01:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |