The Triumph Dolomite Club - Discussion Forum http://forum.triumphdolomite.co.uk/ |
|
RUK - Project Recommission 1972 'Dolomite' Auto http://forum.triumphdolomite.co.uk/viewtopic.php?t=32242 |
Page 39 of 55 |
Author: | yorkshire_spam [ Tue May 15, 2018 9:55 am ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
I didn't get much spanner time last night, but I've reattached the exhaust manifold to the head and got the head in place with a couple of studs in to locate it. Next job will be to fit all the studs/bolts and torque down the head. |
Author: | yorkshire_spam [ Fri May 18, 2018 11:48 am ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
Head has been torqued down, cam sprocket re-fitted and timing checked. Let's hope I can get some decent spanner time sometime soon and finish the job. |
Author: | yorkshire_spam [ Wed May 23, 2018 6:24 pm ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
Oh 4r$e. The front most bolt on the rear manifold flange has pulled a thread out of the block before it reached the specified torque. I've swapped the bolt for a UNC stud that goes further into the block, put a nut on it and pulled it up as tight as I dare, but stopped short of the torque in the workshop manual. I'll fill her up with water sometime soon and see what's what. If I'm unlucky I'll end up stripping it all back off and re-taping that hole to a larger thread. Won't that be "fun"? |
Author: | dollyman [ Wed May 23, 2018 6:42 pm ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
https://www.ebay.co.uk/itm/THREAD-TAP-R ... 1438.l2649 These are brilliant for ally, and cheap Had a similar thing the other day on a modern. Tony. |
Author: | yorkshire_spam [ Wed May 23, 2018 7:18 pm ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
Quote:
https://www.ebay.co.uk/itm/THREAD-TAP-R ... 1438.l2649
Never used one before Tony, what are they like to use?
These are brilliant for ally, and cheap Had a similar thing the other day on a modern. Tony. |
Author: | dollyman [ Wed May 23, 2018 7:33 pm ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
Very easy, just take your time and make sure you keep the drill and tap square when using. They really are good Some people have found watching a you tube video helpfull, or practice first on a scrap piece ally or steel. Tony. |
Author: | yorkshire_spam [ Wed May 23, 2018 8:49 pm ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
Well the manifold isn't leaking water.... But it won't start AND the bypass tube is peeing water out. So, manifold will have to come back off. Edit: It turns out that I'm a moron. I took the cam cover off and turned the engine over by hand.... at the top of compression stroke on #1 the rotor arm is pointing at the #4 plug lead. DOH! Rookie error! |
Author: | dollyman [ Wed May 23, 2018 11:00 pm ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
How many times have we all done that Tony. |
Author: | yorkshire_spam [ Thu May 24, 2018 8:45 am ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
Quote:
How many times have we all done that
My excuse is too much time spent working on OHV engines not OHC.... on the ohv if the cam timing is right and you havent taken the dizzy out then the ignition timing is still right.... with the separate drive to the dizzy on the OHC engines you can get the crank and the cam timed up right but still have the dizzy out by 180deg.Tony. Obvious really, but I clearly wasn't paying attention! |
Author: | dollyman [ Mon May 28, 2018 10:11 pm ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
One job always seem's to make another, but there must be light at the end of tunnell now Tony. |
Author: | yorkshire_spam [ Mon May 28, 2018 10:34 pm ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
Quote:
One job always seem's to make another, but there must be light at the end of tunnell now
As we are planning to use the car for the RBRR later this year (and other events too) I need it in the best shape possible... so no "ignore the problem until later"
Tony. |
Author: | James467 [ Thu May 31, 2018 9:53 am ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
I got my timing chain kit from Robsport Sam. |
Author: | yorkshire_spam [ Thu May 31, 2018 11:06 am ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
Quote:
I got my timing chain kit from Robsport Sam.
Funny you should say that.... I picked up a package from the mail depot this morning. Sent by Robsport on Tuesday. |
Author: | James467 [ Fri Jun 01, 2018 7:23 pm ] |
Post subject: | Re: RUK - Project Recommission 1972 'Dolomite' Auto |
I can't think of anything else engine wise which should be a problem, bottom end should be fine, you're doing the timing chain, I have done the carbs, Water pump is a brand new ceramic ring pump, I set the valve clearances and the cam looks good, rad is brand new. I have a front cover seal if you want me to post it to you. Remember when you refit the kickdown cable to make sure it is adjusted correctly. Sorry, you probably already know that! Did you get the prop balanced in the end? Love that little car! |
Page 39 of 55 | All times are UTC+01:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |