The Triumph Dolomite Club - Discussion Forum http://forum.triumphdolomite.co.uk/ |
|
DTR - Project Recommission 1972 'Dolomite' Manual http://forum.triumphdolomite.co.uk/viewtopic.php?t=32879 |
Page 1 of 22 |
Author: | lazeruspete [ Wed Jul 26, 2017 10:22 pm ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
Great find and save, I'm looking forward to watching this progress |
Author: | SprintMWU773V [ Thu Jul 27, 2017 9:52 am ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
I'll be interested to see the extent of the repairs needed and of course look forward to seeing the repairs take shape. It's fair to say James that you now have Obsessive Dolomite Hoarding Disorder or ODHD! Great find though, and to be so local and free is even better. Similar to how I found my old 1500HL. |
Author: | James467 [ Thu Jul 27, 2017 10:33 am ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
Thanks chaps, I'm going to have a really good look over it this weekend especially that front end. I'll get the inspection camera into the box sections as well. Need to see if it turns over by hand. Have been through my stash and I have points, cap etc... so if I get a battery I should be able to see if it will fire up at the weekend. |
Author: | Jon Tilson [ Thu Jul 27, 2017 11:23 am ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
I notice it has the shallower tunnel tray from a later single rail box car. Is reverse next to 3rd or 1st? It may have the later single rail overdrive box fitted from a later car when the o/d was converted. I can probably find you a 3 rail non overdrive box but I cant remember if I converted most of my boxes of this type to overdrive. You can play a lot of mix and match between 3 rail and single rail boxes and take advantage of the stronger TR7 laygear, but there are some caveats too. If the box in it works well I'd just go with it. I'm surprised this works with the non o-d exhaust though. I had to change the centre section when I converted ERO about 12 years ago now. To get the CDSE bergs running sweet you will I suspect need to do the minute O rings under the plastic lozenges. I would reserve judgement depending on how you get on with them. Front end looks to have suffered but not too badly. I await developments with interest. Jonners |
Author: | Mad Mart [ Thu Jul 27, 2017 12:41 pm ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
Quote: It's fair to say James that you now have Obsessive Dolomite Hoarding Disorder or ODHD! |
Author: | James467 [ Thu Jul 27, 2017 1:27 pm ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
Well Mart, I have been conversing with him a lot recently, oh my god even my vocabulary is better hanging around with him. It's a single rail Jonners, looks to have been converted a while ago. I agree, I think as long as the box works well then I'll stick with it. It's part of the history of the car. Checked the engine number and it matches up so the block hasn't been changed. Untitled by james_shephard_uk, on Flickr I have a knock around with my trusty bodywork hammer today, if there's rust this will find it! Untitled by james_shephard_uk, on Flickr The rear of the car is solid, boot floor is mint, the inside of the boot has a thick coating of black ziebart, there's that familiar smell when you open the boot! Outer sills are just mint, inners and outers. They are original as they have the bottom lip bit. Behind the splash shields is clean, theres a small hole at the bottom of the drivers side sill here, a tiny fix but in a pain in the arse position. Doors are perfect, obviously the Ziebart has done its business here. A posts have some surface rust but no holes like RUK. Engine bay and chassis legs are perfect. Haven't checked behind the servo yet, will do that when I pull it off. The main problem areas are at the front. The lower outer valence on the passengers side has some holes, I'll have to do the same repair as I did before. The outer upper valence had some filler in and is holed around the headlights, this is going to require some fab work here. The wings have a few small holes in, nothing bad. Haven't had the lights off yet so I need to will need to check the headlamp panels but they seem fine after my test of shake the light and see if any rust falls out! I hammered away at the inner valence outers and they really do seem to be solid. The inner valence behind the rad does have some holes. I should be able to repair these with the rad out. I pulled the sender out of the fuel tank and as was to be expected the inside is pretty manky. It's going to need a Bilt Hamber clean and a pressure test. I suspect that it will have a couple of pinholes in it and will need a repair. I popped a battery in and it does turn over and has oil pressure. The radio works and was tuned to Heart, as soon as I turned it on Queen, Radio Ga Ga was playing!! I think the front seats have been replaced as well, the runners on the front are the later type that you have to pull the lever to the side rather than depress it as on the early cars. |
Author: | sprint95m [ Thu Jul 27, 2017 2:18 pm ] |
Post subject: | Okay....... |
Please do note, the wiring has been altered to get the tachometer working (assuming it does work?). Ditch the CDSEs and fit the later CDs. Unleaded and the temperature compensator O -rings are a bad combination…. T2000 CD150s are the same save for the needles. What is an early tachometer worth? Ian. |
Author: | James467 [ Thu Jul 27, 2017 2:44 pm ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
Quote: Please do note, the wiring has been altered to get the tachometer working (assuming it does work?).
Yep, I'm aware of how the rev counter works on early 1850s (given that I own another!! ), the wiring hasn't been touched, it isn't even connected.Quote: Ditch the CDSEs and fit the later CDs. Unleaded and the temperature compensator O -rings are a bad combination….
To be honest with you Ian, no, I'd rather not. The o rings that Burlen now supply are compatible with unleaded fuel so won't be an issue. I'll rebuild them as I did on RUK and replace them and any other parts as necessary, I'm going to keep it as an original early car with sympathetic upgrades, headlights, fan etc...T2000 CD150s are the same save for the needles. I buffed the paint up a bit and it came up very well. It has some places where it has polished through, I may respray it but before I do anything else I want to do a compression test, get the engine running then do a leakdown test. |
Author: | James467 [ Fri Jul 28, 2017 12:51 pm ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
Wow, NWL was just as bad and that had an MOT as well. Although the MOT tester at the time did tell me that it wouldn't go through another MOT the way that it was! I have been thinking about the best way to tackle things on the car. I don't know the condition of the clutch so rather than faff around guessing I will pull the engine and the box out to replace it. This will then give me excellent access in the engine bay to do the welding on the front inner valence and get to the bulkhead without having to work upside down. I'll also have better access for the brake pipes and I can pull the rack out and recondition it as well plus I'll have an easier time moving the car around with no engine in. I can dress the engine, clean it up etc... recondition and fit all of the ancillaries with it out on the engine stand and also check the gearbox over. I really don't like the ziebarted engine bay, but should I be keeping it or cleaning it off? My gut feeling is that as much as I don't like it, it should remain as it is part of the history of the car. |
Author: | AndyTriumph [ Fri Jul 28, 2017 6:00 pm ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
Engine is all original. From memory gearbox had problems. Just wanted to say how pleased we are that the car has gone to such a good home. Also what a pleasure it was in all our dealings with the Club and its members in person and in the forum. Best regards Andy |
Author: | Ron1966 [ Fri Jul 28, 2017 8:50 pm ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
It could not have gone to a better home, James's work and attention to detail is superb. Will be watching with great interest. It is amazing how these Dolomites keep appearing after being mothballed for so long. |
Author: | Mahesh [ Sat Jul 29, 2017 3:01 pm ] |
Post subject: | Re: DTR - Project Recommission 1972 'Dolomite' Manual |
Nice one James At the rate your sorting them out, let's hope some more come your way, and back on the road. |
Page 1 of 22 | All times are UTC |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |