The Triumph Dolomite Club - Discussion Forum

The Number One Club for owners of Triumph's range of small saloons from the 1960s and 1970s.
It is currently Thu Mar 28, 2024 10:39 pm

All times are UTC




Post new topic  Reply to topic  [ 15 posts ] 
Author Message
 Post subject: Diagnosing noises
PostPosted: Mon Jun 18, 2018 12:24 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Mon Jan 05, 2015 12:42 pm
Posts: 309
Location: Ashington, West Sussex
Hiya all!

Just looking for a bit of advice really, I'm getting metal on metal noise when going over bumps. I've got a few ideas what it could be - I'm thinking the anti roll bar mounts, or possibly subframe mounts? But how do you know when they've had it? How do I know what's gone?

Is there anything down there that if I unscrew it, I won't be able to put it back together without clamps or tools other than sockets and spanners? I don't want this getting me in trouble!

Many thanks to you all!

_________________
HQentity (Kyle)

1975 TRIUMPH DOLOMITE 1850 in Honeysuckle (Nina) 2015-2020
Image

"The harder the conflict, the more glorious the Triumph." - Thomas Paine


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Tue Jun 19, 2018 5:56 pm 
Offline
TDC Member

Joined: Sun Mar 16, 2008 2:52 pm
Posts: 2303
Hi Kyle, Elusive noises are always good fun to track down. One advantage of owning a car for a long time is you acquire a 6th sense for what the problem is. Now if your intuition says "ARB" then you are probably right. At the rear the ARB is bolted to the trailing arms and the bolts do seem to work loose. Simple job with 2 spanners when its on axle stands. I found mine by noticing that if I went over a speed bump straight so that both wheels went up and down together, no problem, If I went over it skew, I'd get a clunk.
At the front the ARB has inner and outer bushes. Both wear and the inner brackets can fracture. Easy to spot those. Its rather more complicated to fix as the front has to be on axle stands while the lower wishbones are raised to get the outer joints in place. Doing this symmetrically is the tricky bit. Don't forget the cylindrical spacers inside the lower arms.
Other favourite places for knocks and rattles at the back are the trailing arm bushes and the tie rod. Both ends. In my experience standard shock absorbers don't seem to wear much. A lot will depend on the sort of roads you drive on.
Try lifting and bouncing on each corner of the car in turn ( better with 2 people ) and then lifting and bouncing centrally on the front / rear bumpers for a quick diagnosis.
HTH,
Tony.


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Tue Jun 19, 2018 6:10 pm 
Offline
TDC West Mids Area Organiser
User avatar

Joined: Thu Sep 28, 2006 1:13 pm
Posts: 13316
Location: Over here...can't you see me?
Check your wheel bearings.


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Tue Jun 19, 2018 9:21 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Tue Oct 03, 2006 5:52 pm
Posts: 7566
Location: Halifax, West Yorkshire
The tie bar bushes are one of the first things to go. I replaced mine with SuperFlex and they're still in fine shape.

_________________
Toledo Man

West Yorkshire Area Organiser & forum moderator
Meetings take place on the first Wednesday of the month at 8.00pm at The Old Brickworks, Wakefield Road, Drighlington, Bradford, BD11 1EA

1972 Dolomite 1850 auto (NYE 751L - Now for sale)
2003 Volvo XC90 D5 SE (PX53 OVZ - The daily driver)
2009 Mercedes-Benz W204 C200 CDI Sport (BJ58 NCV - The 2nd car)
1991 Toyota Celica GT (J481 ONB - another project car)
Former stable of SAY 414M (1974 Toledo), GRH 244D (1966 1300fwd), CDB 324L (1973 1500fwd), GGN 573J (1971 1500fwd), DCP 625S (1977 Dolomite 1300) & LCG 367N (1975 Dolomite Sprint) plus 5 Acclaims and that's just the Triumphs!

Check my blog at http://triumphtoledo.blogspot.com
My YouTube Channel with a bit of Dolomite content.

"There is only one way to avoid criticsm: Do nothing, say nothing and BE nothing." Aristotle


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Tue Jun 19, 2018 9:51 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Mon Jan 05, 2015 12:42 pm
Posts: 309
Location: Ashington, West Sussex
Thanks very much for your time you lovely people. :eyes4u:

Tony, your diagnosis about your speed bumps is exactly whats happening with me - if ever I round a corner over a speed bump, I'll get a bit of clunking. How do I know they're gone? Am I looking for the bushes to be too soft? Cracked? Play in the ARB

I did give bumping the corners a go to see if I could replicate the clunking myself so I knew where the problem was, but I couldn't get it to go. Maybe I need someone a bit heavier! :roll:

Checking wheel bearings, is that just spinning the wheels and making sure they move freely?

I'll check the tie bar bushes, thanks! Is that just the same concept as the ARB bushes as mentioned above then? :) Thanks!!

_________________
HQentity (Kyle)

1975 TRIUMPH DOLOMITE 1850 in Honeysuckle (Nina) 2015-2020
Image

"The harder the conflict, the more glorious the Triumph." - Thomas Paine


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Wed Jun 20, 2018 6:46 am 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Tue Oct 03, 2006 5:52 pm
Posts: 7566
Location: Halifax, West Yorkshire
The tie bars run alongside the front ARB. There's a couple of bushes at the front end where they go through the front subframe. This is what mine was like back in April 2009.
Image
Image
With the front wheel bearings, you do indeed spin the wheel to check for any noises (there should be none) and you wiggle the wheel slide to side and top to bottom to check for excessive play. The bearings are tapered to there should be a small amount of free play (most MoT testers don't know this).

_________________
Toledo Man

West Yorkshire Area Organiser & forum moderator
Meetings take place on the first Wednesday of the month at 8.00pm at The Old Brickworks, Wakefield Road, Drighlington, Bradford, BD11 1EA

1972 Dolomite 1850 auto (NYE 751L - Now for sale)
2003 Volvo XC90 D5 SE (PX53 OVZ - The daily driver)
2009 Mercedes-Benz W204 C200 CDI Sport (BJ58 NCV - The 2nd car)
1991 Toyota Celica GT (J481 ONB - another project car)
Former stable of SAY 414M (1974 Toledo), GRH 244D (1966 1300fwd), CDB 324L (1973 1500fwd), GGN 573J (1971 1500fwd), DCP 625S (1977 Dolomite 1300) & LCG 367N (1975 Dolomite Sprint) plus 5 Acclaims and that's just the Triumphs!

Check my blog at http://triumphtoledo.blogspot.com
My YouTube Channel with a bit of Dolomite content.

"There is only one way to avoid criticsm: Do nothing, say nothing and BE nothing." Aristotle


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Wed Jun 20, 2018 9:22 am 
Offline
TDC Member

Joined: Thu Sep 28, 2006 10:06 pm
Posts: 1164
Location: Bristol
I have found that it can be difficult to see if the front tie bar bushes have worn without taking them out as they can wear on the inside and which allows the tie bar to rub on and wear the subframe. It is well worth fitting poly bushes in place of the original rubber type as they last.


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Wed Jun 20, 2018 9:53 am 
Offline
TDC West Mids Area Organiser
User avatar

Joined: Thu Sep 28, 2006 1:13 pm
Posts: 13316
Location: Over here...can't you see me?
Quote:
I have found that it can be difficult to see if the front tie bar bushes have worn without taking them out as they can wear on the inside and which allows the tie bar to rub on and wear the subframe. It is well worth fitting poly bushes in place of the original rubber type as they last.
I would concur with this, but the symptomatic noise here is a metal on metal squeak which persists long before any 'clonk', the latter generally requiring at least one bush to have worn to the extent it falls away from the car! Interestingly, I've found the tie bar wears rather than the subframe hole enlarging, which is good in that the tie bar is far easier to replace!

I'd still look at wheel bearings first/as well as; in my opinion, a far more common malady requiring adjustment or replacement.


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Wed Jun 20, 2018 5:59 pm 
Offline
TDC Member

Joined: Sun Mar 16, 2008 2:52 pm
Posts: 2303
I forgot to enquire; are these metal on metal noises at the front or the back. Or 1/2 way along ?
Doing the easy bits first, if the noises are central underneath the car I'd look at the gearbox mount. This gets oil on it from the gearbox / O.D. and goes soggy. You may get clutch judder with this as well. If you have a non-O.D. box there are 2 small cotton reel mounts. The rubber separates from the metal of the mount. The other possibility is the exhaust bracket that attaches to the back of the gearbox has broken, so the exhaust is waggling around.
Noises at the back end are a bit more difficult to locate on the Dolomite as ( for instance) the trailing arm is in constant downwards compression from the rear spring when jacked up for checking. So to check the rear bush you need to support the back of the car solidly on axle stands then with a strong metal bar, see if you can detect any movement in the bush when you lever upwards between the trailing arm and the bush.
Similarly in the same state, if you can lift the front end of the trailing arm against its bush its time for replacement. I do this with a large crowbar and a large log as a fulcrum point inboard of the trailing arm.
A failed tie rod rear bush you can pretty much see by visual inspection. The front bush can be tested with a narrow lever between the tie-rod and its housing in the same way.
And while you are there check the exhaust mounts. A simple visual check will tell a lot.
HTH
Tony.


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Thu Jun 21, 2018 10:32 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Mon Jan 05, 2015 12:42 pm
Posts: 309
Location: Ashington, West Sussex
Thank you again fo all your help! Given the opportunity I'll try and check tomorrow to see if i can establish what the problem is. :) Thanks for the pictures, am I right to think thats what they're NOT to look like - that they need replacing like that?

I will be definitely taking that advice on board and fitting poly bushes wherever the wear has happened. :) Does it matter if they're not the same on both sides? & I will definitely be checking the bearings too. :)

For me Tony, I'm confident the noises have been coming from the front right (starboard, offside, whatever you prefer :lol: ) portion of the car. I get little to no clutch judder (only really occasionally in reverse). I'm still non-O/D.

Thanks you for your advice, I'll see how I get on! :)

_________________
HQentity (Kyle)

1975 TRIUMPH DOLOMITE 1850 in Honeysuckle (Nina) 2015-2020
Image

"The harder the conflict, the more glorious the Triumph." - Thomas Paine


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Thu Jun 21, 2018 11:16 pm 
Offline
TDC Member
User avatar

Joined: Mon Aug 10, 2015 8:20 pm
Posts: 1293
Location: Shetland / here & there
How about the front shock absorber lower bushing? That makes a squeaky metal grinding sound, I might know this because, well, pictures!

Image

Image

Image

_________________
Current fleet: '75 Sprint, '73 1850, Daihatsu Fourtrak, Honda CG125, Yamaha Fazer 600, Shetland 570 (yes it's a boat!)

Past fleet: Triumph 2000, Lancia Beta Coupe, BL Mini Clubman, Austin Metro, Vauxhall Cavalier MK1 & MK2, Renault 18 D, Rover 216 GSI, Honda Accord (most expensive car purchase, hated, made out of magnetic metal as only car I've ever been crashed into...4 times), BMW 318, Golf GTi MK3 16v x 3


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Fri Jun 22, 2018 12:15 am 
Offline
TDC West Mids Area Organiser
User avatar

Joined: Thu Sep 28, 2006 1:13 pm
Posts: 13316
Location: Over here...can't you see me?
Spinning the wheel will likely be noisy from the pads bearing on the disc. Wobble side to side to check wheel bearings as top to bottom can show any play in lower ball joint.


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Fri Jun 22, 2018 3:24 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Mon Jan 05, 2015 12:42 pm
Posts: 309
Location: Ashington, West Sussex
Okay, so I had a look around today, and all the rubber looks knackered to me. Personally, I think I need to replace everything I've photographed?! Is it a good idea to do it symmetrically on both sides (all of this is RH side)? Surely replacing/unscrewing the wishbone mounts will cause all hell to quite literally break loose with the suspension?


Image

Image

Image

Image

Image

_________________
HQentity (Kyle)

1975 TRIUMPH DOLOMITE 1850 in Honeysuckle (Nina) 2015-2020
Image

"The harder the conflict, the more glorious the Triumph." - Thomas Paine


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Sat Jun 23, 2018 5:48 pm 
Offline
TDC Member

Joined: Sun Mar 16, 2008 2:52 pm
Posts: 2303
Quote:
Thank you again fo all your help! Given the opportunity I'll try and check tomorrow to see if i can establish what the problem is. :) Thanks for the pictures, am I right to think thats what they're NOT to look like - that they need replacing like that?
Does it matter if they're not the same on both sides? & I will definitely be checking the bearings too. :)

For me Tony, I'm confident the noises have been coming from the front right (starboard, offside, whatever you prefer :lol: ) portion of the car.
Yes, the bushes should be the same both sides ideally both rubber or both poly; for nice handling ( One soggy rubber one side and one nice hard poly; bush on the other side might give odd handling. )
Raf's good photos of the shock absorber bush are just what they shouldn't look like :shock:
How can I guess you are on the South Coast and have a nautical interest ?
Cheers for now,
Tony.


Top
   
 Post subject: Re: Diagnosing noises
PostPosted: Sat Jun 23, 2018 11:16 pm 
Offline
TDC Shropshire Area Organiser

Joined: Sun Aug 21, 2011 5:12 pm
Posts: 7014
Location: Highley, Shropshire
OK, from the top, pic 1 the track rod end gaiter is shot and WILL fail an MOT (if presented) This doesn't necessarily mean the track rod end is shot, you need further wiggling tests to ascertain this, If not, the club do gaiters to replace the duff ones.

Pic 2 The tie bar bush and antiroll bar bush don't look THAT bad, The tie bar bush always shows a big gap at full extension, even when new.

Pic 3 the antiroll bar link, i'm gonna be controversial here and say that's probably OK for another 10 years! Mine look like that on the Carledo and are still working fine and not knocking.

Pic 4 The inner upper wishbone bushes, these LOOK horribly perished, but the bit you can see is not the bit that does the work. I've replaced loads that look like this (with poly) and i've still had to press them out, they've been fine! My money says they are not your culprit!

Pic 5 The rear subframe bush, this is knackered, get some poly in there pronto! When changing it, check the cups in the subframe and the conical washers underneath the nuts too. You can change just the rear bushes, but best to do both sides at once!

And check the lower shock mount bush as per Rafe's post, this is a common fail point, especially if aftermarket fancy shox have been fitted. I looked at mine on the Carledo recently, prior to it's MOT, as I have Gaz fitted. What I found was good news as far as the bushes were concerned, no wear either side, but the N/S bolt had snapped clean through and the 2 broken ends were only holding in by gravity and friction. No knocks or clonks to tell me it had failed though! I fitted new bolts both sides, just in case!

Steve

_________________
'73 2 door Toledo with Vauxhall Carlton 2.0 8v engine (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine (The Dolomega)
'72 Triumph 1500FWD in Slate Grey, Now with RWD and Carledo powertrain!

Maverick Triumph, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 50 years. PM for more info or quotes.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 15 posts ] 

All times are UTC


Who is online

Users browsing this forum: djw113uk, Google, Trendiction and 27 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited