The Triumph Dolomite Club - Discussion Forum

The Number One Club for owners of Triumph's range of small saloons from the 1960s and 1970s.
It is currently Thu Mar 28, 2024 10:01 pm

All times are UTC




Post new topic  Reply to topic  [ 12 posts ] 
Author Message
 Post subject: 1500 to smoke or melt?
PostPosted: Mon Dec 03, 2012 4:55 am 
Offline
Future Club member hopefully!
Future Club member hopefully!

Joined: Fri Aug 13, 2010 8:50 pm
Posts: 567
Location: newton abbot, south devon
Hi there. Years ago I went through 1500 engines like they were going out of fashion for some reason even though I waited at least 500+ miles before gradually going above 3000 rpm.
I'm now getting a 1500 that's been rebuilt we think. What can I do to keep it strong on the bottom end? What mods have people tried?
I only have a 4 speed box so would like the thought of gunning it without killing it. Thanks, Mark.


Top
   
PostPosted: Mon Dec 03, 2012 9:37 am 
The best you can do is give it some good oil.
Currently the best and preferred choice is Valvoline VR1 and change it with the filter every 3k for longevity. And make sure it's an anti-drain filter!


Top
   
PostPosted: Mon Dec 03, 2012 7:10 pm 
Quote:
The best you can do is give it some good oil.
Currently the best and preferred choice is Valvoline VR1 and change it with the filter every 3k for longevity. And make sure it's an anti-drain filter!
Hi there,
I'm trying to keep my 1500HL's bottom end in good shape too (difficult on motorways with non O/D :roll: )
...The thing is it's due an oil change, would you say this is a good type for everyday driving (as it says for racing on ebay).
otherwise I was thinking of getting some halfords classic 20w50 or Morris' would this 'Valvoline VR1' be better?
Thanks, Tim


Top
   
PostPosted: Mon Dec 03, 2012 7:54 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Wed Jan 23, 2008 5:19 am
Posts: 3210
Location: Old Basing, Hants.
Yes. Vr1 is fine for road use.
Also waiting for the resident ohv expert to stick his head in with some gold advice!
Jod, where are you?

_________________
1978 Sandglow Dolomite 1850HL The Lolomite - MOT pass! (broken again in 55 miles though...)
It's 106 miles to Chicago, we've got a full tank of gas, half a pack of cigarettes, it's dark, and we're wearing sunglasses.
Hit it.
Image


Top
   
PostPosted: Mon Dec 03, 2012 8:51 pm 
Quote:
Yes. Vr1 is fine for road use.
Also waiting for the resident ohv expert to stick his head in with some gold advice!
Jod, where are you?
Is this any better than the halfords or morris' stuff though?


Top
   
PostPosted: Tue Dec 04, 2012 12:32 am 
Quote:
Quote:
Yes. Vr1 is fine for road use.
Also waiting for the resident ohv expert to stick his head in with some gold advice!
Jod, where are you?
Is this any better than the halfords or morris' stuff though?
Hell yes! And only slightly more expensive from eBay. I bought a load in bulk a while back when someone was selling it at £15/5 litres.
It's absolutely fine for road use and will keep wear to a minimum because of its high ZDDP levels.
It's what the majority of classic owners are now using and I haven't heard any complaints yet.


Top
   
PostPosted: Tue Dec 04, 2012 11:03 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Fri Nov 23, 2007 11:33 pm
Posts: 4727
Location: hampshire
Very good question, "Is there a way to make a good 1500?"

Transplant :twisted:

_________________
track action maniac.

The lunatic is out................heres Jonny!


Top
   
PostPosted: Wed Dec 05, 2012 8:43 pm 
Offline
TDC Shropshire Area Organiser

Joined: Sun Aug 21, 2011 5:12 pm
Posts: 7014
Location: Highley, Shropshire
The dodge I have heard of (but not tried as i've not had a 1500 personally, though I have had just about every other size from 948 Herald to Stag V8) is one that can only be done with the engine in bits.
The problem with the 1500 (and later "big crank" 1300s) is one of underlubrication, the factory, in its infinite wisdom, increased the bearing journal diameter without increasing the oil flow to lubricate the bigger surface area created which makes the shells run hotter and wear out quicker, especially when subjected to sustained high revs.
The solution is obvious, cross drill the crank to let more oil onto the bearings and fit a high capacity (or at least a "blueprinted") oil pump to supply the necessary quantities of liquid engineeering!
Years back when i was racing my GT6 there were several people campaigning 1500 Spits and this was what they did to help their engines hold together!

Steve

_________________
'73 2 door Toledo with Vauxhall Carlton 2.0 8v engine (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine (The Dolomega)
'72 Triumph 1500FWD in Slate Grey, Now with RWD and Carledo powertrain!

Maverick Triumph, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 50 years. PM for more info or quotes.


Top
   
PostPosted: Mon Dec 10, 2012 1:32 am 
Offline
Future Club member hopefully!
Future Club member hopefully!

Joined: Fri Aug 13, 2010 8:50 pm
Posts: 567
Location: newton abbot, south devon
When you say cross drill do you mean to turn the crank through 90 degrees and drill through the center again? Also, where can I get a sandwich plate for an oil cooler take off?
Would a pair of hif38s be better than the hs4s? Or I could even get some nice hif44s to fit with some time? Or should I just go for some heavy springs and different needles?


Top
   
PostPosted: Tue Feb 19, 2013 4:54 pm 
yup totally agree change oil at 3k buy the best oil u can afford ive got a 1500 auto and this 3k change has worked well so far so good


Top
   
PostPosted: Thu Feb 28, 2013 11:21 pm 
If you bide your time you could get a good Sprint lump for under £150. Thats only a few quality oil and filter changes :)


Top
   
PostPosted: Fri Mar 01, 2013 6:06 am 
:shock :D : um :D doesnt that defeat the object of owning different types of dollys though !!!


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 12 posts ] 

All times are UTC


Who is online

Users browsing this forum: djw113uk and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited