The Triumph Dolomite Club - Discussion Forum

The Number One Club for owners of Triumph's range of small saloons from the 1960s and 1970s.
It is currently Tue Mar 19, 2024 5:24 am

All times are UTC




Post new topic  Reply to topic  [ 31 posts ]  Go to page 1 2 3 Next
Author Message
 Post subject: Sprint Suspension Set Up
PostPosted: Tue Feb 27, 2018 4:08 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Fri Jan 06, 2017 11:14 pm
Posts: 246
Can someone advise what would be a good front/rear suspension set up for track/road use?

I've heard that Sprints benefit for a soft rear suspension and a harder front setup. Is this correct and what would be suitable springs and shocks to achieve that purpose?

_________________
1972 Spitfire MK IV
1972 Stag
1980 Sprint

1962 Land Rover Series 2a
1961 Land Rover Series 2a (under restoration)
1983 Land Rover Series 3

1995 Suzuki Samurai SJ413

1972 MGB GT (banished for being too tight to fit in it)


Top
   
PostPosted: Tue Feb 27, 2018 4:41 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Tue Oct 15, 2013 9:36 am
Posts: 88
Location: nottingham
I've just fitted Gaz height adjustable dampers with new standard sprint springs from Rimmers. At the same time a full Poly bush kit was fitted. It drives great and now corners impeccably, however i'm glad i didnt fit the uprated springs as it is borderline tolerable on the road as it is.

It is sitting about as low as i dare go, although its not seen a track yet it feels like it would be the perfect setup considering how well its handling been thrown in to the twisties.

I did a fair bit of forum digging before taking the plunge on standard springs. Seems like the way to go especially if you want to use it on the road also.

_________________
1980 Russet 1850hl


Top
   
PostPosted: Tue Feb 27, 2018 10:34 pm 
Offline
TDC Shropshire Area Organiser

Joined: Sun Aug 21, 2011 5:12 pm
Posts: 7005
Location: Highley, Shropshire
The front of a Sprint will tolerate a stiffer spring, maybe up to 175lb but I wouldn't put anything much over stock poundage in the back unless you have an LSD. An open diffed car will just cock a rear wheel and lose traction at just the wrong moment! And Gaz ASP shox all round for ride height control and fine tuning of balance.

As you correctly say, a Sprint (or most any front engined RWD car) works best with a stiffish front end and a softish rear.

It's not a Sprint admittedly, but a lighter 2 door. And yes, i'm a hoon! Power on into the apex of Quarry corner at Castle Coombe and she's trying really hard to lift the inside rear. It didn't happen this time but on several other (maybe quicker) laps I was getting some spin up. Guess what? I can't afford an LSD! Car has stock Sprint front springs and stock Toledo rears, all over ASP Gaz.

Image

Steve

_________________
'73 2 door Toledo with Vauxhall Carlton 2.0 8v engine (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine (The Dolomega)
'72 Triumph 1500FWD in Slate Grey, Now with RWD and Carledo powertrain!

Maverick Triumph, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 50 years. PM for more info or quotes.


Top
   
PostPosted: Thu Mar 01, 2018 2:49 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Fri Jan 06, 2017 11:14 pm
Posts: 246
GAZ have been mentioned (twice).

So, no SPAX or AVO?

_________________
1972 Spitfire MK IV
1972 Stag
1980 Sprint

1962 Land Rover Series 2a
1961 Land Rover Series 2a (under restoration)
1983 Land Rover Series 3

1995 Suzuki Samurai SJ413

1972 MGB GT (banished for being too tight to fit in it)


Top
   
PostPosted: Thu Mar 01, 2018 2:51 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Fri Jan 06, 2017 11:14 pm
Posts: 246
Quote:
I've just fitted Gaz height adjustable dampers with new standard sprint springs from Rimmers. At the same time a full Poly bush kit was fitted. It drives great and now corners impeccably, however i'm glad i didnt fit the uprated springs as it is borderline tolerable on the road as it is.

It is sitting about as low as i dare go, although its not seen a track yet it feels like it would be the perfect setup considering how well its handling been thrown in to the twisties.

I did a fair bit of forum digging before taking the plunge on standard springs. Seems like the way to go especially if you want to use it on the road also.
Thanks. It will be 80% road use and maybe 20% sprint and track use.

When you write that it is as low as you dare go, is that because of the shock settings or the springs?

_________________
1972 Spitfire MK IV
1972 Stag
1980 Sprint

1962 Land Rover Series 2a
1961 Land Rover Series 2a (under restoration)
1983 Land Rover Series 3

1995 Suzuki Samurai SJ413

1972 MGB GT (banished for being too tight to fit in it)


Top
   
PostPosted: Thu Mar 01, 2018 3:20 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Tue Oct 15, 2013 9:36 am
Posts: 88
Location: nottingham
Quote:
Quote:
I've just fitted Gaz height adjustable dampers with new standard sprint springs from Rimmers. At the same time a full Poly bush kit was fitted. It drives great and now corners impeccably, however i'm glad i didnt fit the uprated springs as it is borderline tolerable on the road as it is.

It is sitting about as low as i dare go, although its not seen a track yet it feels like it would be the perfect setup considering how well its handling been thrown in to the twisties.

I did a fair bit of forum digging before taking the plunge on standard springs. Seems like the way to go especially if you want to use it on the road also.
Thanks. It will be 80% road use and maybe 20% sprint and track use.

When you write that it is as low as you dare go, is that because of the shock settings or the springs?
If its 80% for road, I'd go standard springs if your fitting stiffer bushes to. Mines an 1850 though so i think your carrying an extra persons weight, 90kg ish.

Its as low as I dare go due to ground clearance, It handles like its on rails but the ground clearance of my subframe and exhaust mounts leaves a little bit to be desired when your faced with a speed bump. The shocks have enough adjustment to pretty much drag the under carriage along the floor.

I'd say Gaz are the most common adjustable damper going on Dollies from what I see. Readily available, good value and on par with competitors.

_________________
1980 Russet 1850hl


Top
   
PostPosted: Thu Mar 01, 2018 3:47 pm 
Offline
TDC Member
User avatar

Joined: Tue Oct 03, 2006 5:48 pm
Posts: 8445
Location: Winscombe, North Somerset, England
I used AVOs on my track Sprint. Had them on for 10+ years and they're still going well. 400lb front springs & 200lb rears. The Sprint was only used for track days and getting to and from the circuit (no trailer queen here). :lol:

Image

_________________
Sprintless for the first time in 35+ years. :boggle2: ... Still Sprintless.

Engines, Gearboxes, Overdrives etc. rebuilt. PM me.


1997 TVR Chimaera 450


Image


Top
   
PostPosted: Thu Mar 01, 2018 7:43 pm 
Offline
TDC Shropshire Area Organiser

Joined: Sun Aug 21, 2011 5:12 pm
Posts: 7005
Location: Highley, Shropshire
There's not that much to choose between the big 3 of Gaz, AVO and Spax. Gaz work out marginally the cheapest and seem to be the best overall quality with Spax having damping and adjuster quality issues and AVO suffering accelerated wear in the lower bush (as well as being the most expensive) This is largely drawn from reports by owners on this forum and is not definitive. I've been running my Gaz for 6 years and nearly 20k road and track miles now, no problems so far........

Steve

I think Mart had an LSD in his track car, AND 175ish horses, which is probably why he was able to run rings round me, every time we were on track together. That and extreme familiarity with Coombe circuit which is his "local" track!

_________________
'73 2 door Toledo with Vauxhall Carlton 2.0 8v engine (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine (The Dolomega)
'72 Triumph 1500FWD in Slate Grey, Now with RWD and Carledo powertrain!

Maverick Triumph, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 50 years. PM for more info or quotes.


Top
   
PostPosted: Fri Mar 02, 2018 9:52 am 
Offline
TDC Member
User avatar

Joined: Tue Oct 03, 2006 5:48 pm
Posts: 8445
Location: Winscombe, North Somerset, England
Yes, my track Sprint did (does) have an LSD. I do remember someone on the forum having trouble with wear in the lower bush but I have not touched my AVOs since I installed them. I can only recall the one case though.

_________________
Sprintless for the first time in 35+ years. :boggle2: ... Still Sprintless.

Engines, Gearboxes, Overdrives etc. rebuilt. PM me.


1997 TVR Chimaera 450


Image


Top
   
PostPosted: Fri Mar 02, 2018 2:10 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Thu Oct 06, 2011 1:13 am
Posts: 3173
Location: The continent
Don't use spax. They are of a bad quality. Avo or GAZ. I had some AVO's made with a uniball as a lower bearing. That did solve the lower bush problems.

Jeroen
Image

Image

_________________
Classic Kabelboom Company. For all your wiring needs. http://www.classickabelboomcompany.com


Top
   
PostPosted: Mon Mar 05, 2018 9:37 am 
Offline
TDC Member
User avatar

Joined: Fri Oct 06, 2006 9:57 am
Posts: 669
Location: Auckland, New Zealand
If it is 80 road and 20 track, then you need a road setup as if you go full race it becomes almost undriveable on the road.

As said with race you need an LSD (worth 2-3 seconds a lap), wider sticky tyres, I run revalved Bilstein shocks, 500lb front and 225 rear springs, plus radically changed steering geometry and heaps more changes.

For your use on road and track I would first fix the brakes with something like a Trackerjack conversion with better pads (standard brakes just aren't up to track work), lower the car no more than 1 inch (lower more and you make losing the back end more likely). Decent tyres, 7/16 rather than the earlier 3/8 wheel studs/nuts. Make sure you've got Avo or GAZ shocks but don't set them too hard. Don't use poly bushes in shocks, go rubber. A decent temperature gauge and oil presuure will allow you to see what is happening when you also put more pressure on lubrication and cooling system.

Then a better seat and fixed belts or you'll be hanging on to the steering wheel to stop you driving from the passenger seat.

Finally protect yourself with decent helmet and overalls - extinguisher with metal bracket bolted to the floor in front of your seat. The Sprint is an old car and its more likely to break something on the track than on the road.

But is hellish good fun!

Geoff

Search YouTube for 'Dolomite Sprint No 20'


Top
   
PostPosted: Mon Mar 05, 2018 1:44 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Fri Jan 06, 2017 11:14 pm
Posts: 246
Quote:
If it is 80 road and 20 track, then you need a road setup as if you go full race it becomes almost undriveable on the road.

As said with race you need an LSD (worth 2-3 seconds a lap), wider sticky tyres, I run revalved Bilstein shocks, 500lb front and 225 rear springs, plus radically changed steering geometry and heaps more changes.

For your use on road and track I would first fix the brakes with something like a Trackerjack conversion with better pads (standard brakes just aren't up to track work), lower the car no more than 1 inch (lower more and you make losing the back end more likely). Decent tyres, 7/16 rather than the earlier 3/8 wheel studs/nuts. Make sure you've got Avo or GAZ shocks but don't set them too hard. Don't use poly bushes in shocks, go rubber. A decent temperature gauge and oil presuure will allow you to see what is happening when you also put more pressure on lubrication and cooling system.

Then a better seat and fixed belts or you'll be hanging on to the steering wheel to stop you driving from the passenger seat.

Finally protect yourself with decent helmet and overalls - extinguisher with metal bracket bolted to the floor in front of your seat. The Sprint is an old car and its more likely to break something on the track than on the road.

But is hellish good fun!

Geoff

Search YouTube for 'Dolomite Sprint No 20'

You made me raring to go!!

_________________
1972 Spitfire MK IV
1972 Stag
1980 Sprint

1962 Land Rover Series 2a
1961 Land Rover Series 2a (under restoration)
1983 Land Rover Series 3

1995 Suzuki Samurai SJ413

1972 MGB GT (banished for being too tight to fit in it)


Top
   
PostPosted: Sun Mar 18, 2018 10:02 am 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Fri Nov 23, 2007 11:33 pm
Posts: 4727
Location: hampshire
I had standard rear and approx 250lb front with AVO all round and slightly lowered and the car was a touch slower than Marts (probably because I am slower!) round Combe and my best time was 1min 30.
The car was fine on the road but the single best mod you can make is use a tyre such as a Toyo 888 or similar as once they get up to temp on track the car is fantastic fun. Spax paint falls off and the adjusters seize and some AVO had an inferior bush arrangement so GAZ units on my Quantum 2+2 kit car were very good with no faults.

_________________
track action maniac.

The lunatic is out................heres Jonny!


Top
   
PostPosted: Sun Mar 18, 2018 10:16 pm 
Offline
TDC Shropshire Area Organiser

Joined: Sun Aug 21, 2011 5:12 pm
Posts: 7005
Location: Highley, Shropshire
Another thumbs up here for the Toyo tyres. the 888s are fantastically sticky, but even the T1R is a useful, grippy tyre, with a good life for a soft compound.

Steve

_________________
'73 2 door Toledo with Vauxhall Carlton 2.0 8v engine (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine (The Dolomega)
'72 Triumph 1500FWD in Slate Grey, Now with RWD and Carledo powertrain!

Maverick Triumph, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 50 years. PM for more info or quotes.


Top
   
PostPosted: Thu Apr 05, 2018 11:04 am 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Fri Jan 06, 2017 11:14 pm
Posts: 246
Does anyone have the model numbers for the front and rear GAZ adjustable shocks?

The TSSC lists GS1-2266 or GP6-2267 for the front and GP6-2268 for the rear. Are these correct?

_________________
1972 Spitfire MK IV
1972 Stag
1980 Sprint

1962 Land Rover Series 2a
1961 Land Rover Series 2a (under restoration)
1983 Land Rover Series 3

1995 Suzuki Samurai SJ413

1972 MGB GT (banished for being too tight to fit in it)


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 31 posts ]  Go to page 1 2 3 Next

All times are UTC


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited