The Triumph Dolomite Club - Discussion Forum

Right, time to return to this now that various other 'projects' have departed. Quick question for the moment: where/who is recommended please for the requisite Payen gasket set. Thanks.
Regards.

_________________
Brompton P-Type, 2008
Moulton APB R18, 200x
Bat-eared Jack Russell, year unknown

Blog: www.ymgw.blogspot.com

http://www.jamespaddock.co.uk/parts.asp ... ehicleId=2

As an aside, while the head is off is an ideal time to give the exhaust manifold and downpipe a little attention. I use a file to make sure both are flat on their mating face. (and consider replacing the studs if they are bad. I had a broken one and 2 manky ones, so drilled out and tapped to 10mm, which causes a small issue that the new gasket needs carefully opening up, and really cap head bolts to replace the studs. But no more blowing gaskets!)

_________________
Clive Senior
Brighton
Driving Toledo fitted with slant 4, sprint OD box and axle. Needs fettling!

I'd like to add that the downpipe should be bolted to the gearbox bracket as well. This will help to prevent the manifold/downpipe joint from leaking and it will stop the exhaust from banging against the chassis rail.

_________________
Toledo Man

West Yorkshire Area Organiser & forum moderator
Meetings take place on the first Wednesday of the month at 8.00pm at The Old Brickworks, Wakefield Road, Drighlington, Bradford, BD11 1EA
1972 Dolomite 1850 auto (NYE 751L - The rolling restoration)
2008 Citroën C4 Grand Picasso 2.0 HDi Exclusive (MA08 WCL - the workhorse)
1995 BMW 318i (M265 PNC - Project Bimmer, the weekend car)
1991 Toyota Celica GT (J481 ONB - the new project car)
Former stable of SAY 414M (1974 Toledo), GRH 244D (1966 1300fwd), CDB 324L (1973 1500fwd), GGN 573J (1971 1500fwd), DCP 625S (1977 Dolomite 1300) & LCG 367N (1975 Dolomite Sprint) plus 5 Acclaims and that's just the Triumphs!

Check my blog at http://triumphtoledo.blogspot.com

"There is only one way to avoid criticsm: do nothing, say nothing and BE nothing." Aristotle

I recently purchased this car from Richard and am working through this job (helped by the replies above). Having got the head off and had it cleaned etc, I'm unsure as to whether I should buy new studs, washers, nuts for the block and head or just cleaning the originals should be fine?

Thanks

Stephen

Some new head nuts is always a good idea. Unless the studs are noticeably devoid of thread, they should be fine, just give them a clean up and a film of light oil.

Steve

_________________
2 door '73 Toledo with Vauxhall Carlton 2.0 8v engine OWF 797M (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine EGP 247T (The Dolomega)
'91 Cavalier 2ltr 8v auto
'95 Cavalier 2ltr 16v auto
Spectrum Auto Services, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 45 years and home of Maverick Triumph.PM for more info or quotes.

Cheers Steve, will do.

Thanks also for the recommendation of Head Technique - picked it up yesterday but looks so good to put the rest of the car to shame!

Stephen

Maybe not everyone's opinion.... but if you can re-use head studs and they are in good condition do so. If you are short of a couple I might have some in a box somewhere you can have.
If they are not re-usable (and you can't get some old ones in good condition) then consider an ARP kit. They are expensive, but worth it.
Personally I'm not sure how much I''d trust new replacements from anyone other than ARP. Most probably it's my paranoia and they'd be fine.

_________________
http://yorkshire-spitfire.blogspot.com/

if buying new nuts/washers you MUST NOT use std nuts or washers. They need to be specific head nuts and hardened washers. Otherwise you will be doing the gasket again shortly....

Canley classics are a good source of OHV stuff.

Oh, and I have always reused the studs/nuts/washers unless damaged.

_________________
Clive Senior
Brighton
Driving Toledo fitted with slant 4, sprint OD box and axle. Needs fettling!

Our local friends at Fitchetts also have the correct head nuts in stock.

Steve

_________________
2 door '73 Toledo with Vauxhall Carlton 2.0 8v engine OWF 797M (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine EGP 247T (The Dolomega)
'91 Cavalier 2ltr 8v auto
'95 Cavalier 2ltr 16v auto
Spectrum Auto Services, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 45 years and home of Maverick Triumph.PM for more info or quotes.

I am learning something new almost every week on this discussion board. What is special about head nuts and washers?

I think there or should be high tensile steel

Dave

I've fitted most of the engine and ancillaries back together now but can't seem to see the block drain that was mentioned (or at least what I was expecting). Is this usually a tap or a brass or similar plug?

Thanks

Stephen

I think on the 1500 block it's the "open" hole in the group of three "knobbles" shown here bottom left.
Certainly on the later engines/cars it's just a hex head plug not a tap.



Dunno why images on postimg seem broken.... try something else....
I yoinked an image out of google image search...

_________________
http://yorkshire-spitfire.blogspot.com/

Thank you - easily spotted with that picture to help!

A good poke about in the hole with wire is often required as they can be so badly blocked up....
In fact I strongly recommend flushing the block, I push a garden hose, cut off dead square, against the drain hole. Obviously need to have another hose off somewhere, otherwise you will get very wet. And flushing the heater matrix is a fine idea while you are at it. Both ways, several times.

_________________
Clive Senior
Brighton
Driving Toledo fitted with slant 4, sprint OD box and axle. Needs fettling!