The Triumph Dolomite Club - Discussion Forum

The Number One Club for owners of Triumph's range of small saloons from the 1960s and 1970s.
It is currently Fri Mar 29, 2024 2:37 am

All times are UTC




Post new topic  Reply to topic  [ 12 posts ] 
Author Message
 Post subject: 1300 Halogen Bulbs
PostPosted: Fri Oct 08, 2021 10:32 pm 
Offline
TDC Member

Joined: Wed Oct 07, 2020 8:17 pm
Posts: 24
Location: Southampton
Evening all,

I'm going to be looking at upgrading the headlamps on my 1300 to the H4 Halogen bulbs in the near future.
I have done a search on the forum and all I could find was the procedure to upgrade the HL / Twin Headlamp setup.

So, a quick question is the process the same and it's best to fit relays - or are they not needed for the 1300 ?
If they are needed, is there a plug n play loom available?

Thank you,

_________________
Wayne Lee


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Sat Oct 09, 2021 12:43 am 
Offline
TDC Shropshire Area Organiser

Joined: Sun Aug 21, 2011 5:12 pm
Posts: 7014
Location: Highley, Shropshire
I won't definitively say ALL, but most square headlights made for the Dolomite and Toledo range (also Allegro, Hillman Avenger et al) are made to accomodate the 410 tungsten bulb, rather than the H4 Halogen (AKA 472) There ARE Halogen conversion bulbs available, I have them in the Carledo, but can't remember their number at this time of night and the garage is dark and cluttered, I'll check tomorrow!

These bulbs are the same 65/55w output as the stock H4 (the 410 is a measly 45/40w) and have not, in the 10 years i've been running them, given any trouble to my dipswitch and wiring.

The real killer on the 4 lamp cars is having 4 main beams (at least 260w) going at once, a problem the 2 lamp cars don't have. Relays, if you do decide on belt and braces, would be wired exactly the same as the 4 lamp cars, diagrams are elsewhere on these pages.

If you intend to fit a couple of long range driving lights to supplement the main beams, i'd recommend relays for the same reason as on the 4 lamp cars.

Steve

_________________
'73 2 door Toledo with Vauxhall Carlton 2.0 8v engine (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine (The Dolomega)
'72 Triumph 1500FWD in Slate Grey, Now with RWD and Carledo powertrain!

Maverick Triumph, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 50 years. PM for more info or quotes.


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Sat Oct 09, 2021 5:27 pm 
Offline
TDC Member

Joined: Wed Oct 07, 2020 8:17 pm
Posts: 24
Location: Southampton
Hi Steve,

Thanks for the detailed reply.

I had a feeling that may be the case with the single headlamp set up, and the standard wiring should be OK.
The reflective ls on my lights are looking a little corroded, so I managed to get some early Metro headlights on eBay, which I believe can be fettled to fit - the H4s would be going into these.

I do plan to fit some driving/spot lamps at some point, mainly for aesthetics, but will be running these on a separate toggle switch & relayed loom.

Thanks again,
Wayne

_________________
Wayne Lee


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Sat Oct 09, 2021 7:56 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!

Joined: Tue May 06, 2014 4:38 pm
Posts: 535
Location: South Benfleet, Essex
Quote:
I won't definitively say ALL, but most square headlights made for the Dolomite and Toledo range (also Allegro, Hillman Avenger et al) are made to accomodate the 410 tungsten bulb, rather than the H4 Halogen (AKA 472) There ARE Halogen conversion bulbs available, I have them in the Carledo, but can't remember their number at this time of night and the garage is dark and cluttered, I'll check tomorrow!

These bulbs are the same 65/55w output as the stock H4 (the 410 is a measly 45/40w) and have not, in the 10 years i've been running them, given any trouble to my dipswitch and wiring.

The real killer on the 4 lamp cars is having 4 main beams (at least 260w) going at once, a problem the 2 lamp cars don't have. Relays, if you do decide on belt and braces, would be wired exactly the same as the 4 lamp cars, diagrams are elsewhere on these pages.

If you intend to fit a couple of long range driving lights to supplement the main beams, i'd recommend relays for the same reason as on the 4 lamp cars.

Steve
As Steve has said, the normal substitute H4 quartz-halogen bulb (P45t mounting flange like the factory-fitted 410 45/40W glass-envelope bulb) is 60/55W, but one might still be able to get P45t flanged, 100/80W quartz-halogen bulbs, like those fitted to my 1973 VW Type 2.

Image

From as early as the mid-1970s, quartz-halogen, 60/55W, H4 bulbs, with P45t mounting flanges, have been available to substitute, into the ordinary non-H4 headlamp units, as I did in 1976, with my British specification, 1973 VW Type 2; resulting in vastly improved headlamp performance, on both main & dipped beams.

In 1989, I learned of 100/55W & 100/80W, P45t flanged H4 bulbs, of which I used the latter to further upgrade my headlamps; also upgrading the circuit with heavy-duty cable and two Hella 40A relays (one each, for main & dipped beams).

These P45t flanged H4 bulbs, have been known to be available in 60/55W, 100/55W, 100/80W & 130/90W power ratings.

One can also obtain P45t to P43t adapters, which enable one to fit the more commonly available, standard & uprated P43t flanged quartz-halogen into headlamps designed for P45t flanged bulbs like the 410.

The P43t flanged H4 bulbs, have been known to be available in 60/55W, 100/55W, 100/80W, 130/90W & 160/100W power ratings.

_________________
Regards.

Nigel A. Skeet

Independent tutor of mathematics, physics, technology & engineering, for secondary, tertiary, further & higher education.

https://www.linkedin.com/profile/view?id=308177758

Upgraded 1974 Triumph Toledo 1300 (Toledo / Dolomite HL / Sprint hybrid)

Onetime member + magazine editor & technical editor of Volkswagen Type 2 Owners' Club


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Sun Oct 10, 2021 4:49 am 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Mon Jun 03, 2013 5:48 pm
Posts: 1635
I would fit relays, its a 10 minute job and could save problems later on.

_________________
Some people are like Slinky's, they serve no real purpose in life but bring a smile to your face when you push them down the stairs.


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Sun Oct 10, 2021 9:06 am 
Offline
Future Club member hopefully!
Future Club member hopefully!

Joined: Mon Dec 03, 2012 6:04 pm
Posts: 1549
The one word of caution I would say about all this is, just because a bulb will fit doesn't mean it is compatible with the headlight unit. The problem with fitting a more powerful and different type of bulb to one the unit is designed for is, the possibility of dazzling other drivers. You see this with illegal and dangerous HID conversions.

Whether that would be an issue with the Dolly headlights, I have no idea. I don't know how much difference there is between a tungsten and halogen bulb and whether the extra output would a problem for the units reflectors.


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Sun Oct 10, 2021 11:25 am 
Offline
TDC Member

Joined: Wed Oct 07, 2020 8:17 pm
Posts: 24
Location: Southampton
Thanks all for the additional info,

The Metro Headlamps I plan to install have the H4 bulb as standard, so I'm confident they will be ok for compatibility - and since I plan, at some point when it's eventually ready, to use her as a summer "daily" I will add relays whilst I'm fiddling about (just that I hate electrics !).

Thanks again,

Wayne

_________________
Wayne Lee


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Sun Oct 10, 2021 9:11 pm 
Offline
TDC Shropshire Area Organiser

Joined: Sun Aug 21, 2011 5:12 pm
Posts: 7014
Location: Highley, Shropshire
Quote:
Quote:
I won't definitively say ALL, but most square headlights made for the Dolomite and Toledo range (also Allegro, Hillman Avenger et al) are made to accomodate the 410 tungsten bulb, rather than the H4 Halogen (AKA 472) There ARE Halogen conversion bulbs available, I have them in the Carledo, but can't remember their number at this time of night and the garage is dark and cluttered, I'll check tomorrow!

These bulbs are the same 65/55w output as the stock H4 (the 410 is a measly 45/40w) and have not, in the 10 years i've been running them, given any trouble to my dipswitch and wiring.

The real killer on the 4 lamp cars is having 4 main beams (at least 260w) going at once, a problem the 2 lamp cars don't have. Relays, if you do decide on belt and braces, would be wired exactly the same as the 4 lamp cars, diagrams are elsewhere on these pages.

If you intend to fit a couple of long range driving lights to supplement the main beams, i'd recommend relays for the same reason as on the 4 lamp cars.

Steve
As Steve has said, the normal substitute H4 quartz-halogen bulb (P45t mounting flange like the factory-fitted 410 45/40W glass-envelope bulb) is 60/55W, but one might still be able to get P45t flanged, 100/80W quartz-halogen bulbs, like those fitted to my 1973 VW Type 2.

Image

From as early as the mid-1970s, quartz-halogen, 60/55W, H4 bulbs, with P45t mounting flanges, have been available to substitute, into the ordinary non-H4 headlamp units, as I did in 1976, with my British specification, 1973 VW Type 2; resulting in vastly improved headlamp performance, on both main & dipped beams.

In 1989, I learned of 100/55W & 100/80W, P45t flanged H4 bulbs, of which I used the latter to further upgrade my headlamps; also upgrading the circuit with heavy-duty cable and two Hella 40A relays (one each, for main & dipped beams).

These P45t flanged H4 bulbs, have been known to be available in 60/55W, 100/55W, 100/80W & 130/90W power ratings.

One can also obtain P45t to P43t adapters, which enable one to fit the more commonly available, standard & uprated P43t flanged quartz-halogen into headlamps designed for P45t flanged bulbs like the 410.

The P43t flanged H4 bulbs, have been known to be available in 60/55W, 100/55W, 100/80W, 130/90W & 160/100W power ratings.
I've not lately seen any of the higher wattage 410 substitute Halogen conversion bulbs being offered (though i've not checked widely) My local factors only stock the 65/55w version, which I regard as quite ample. In my experience, correct headlamp adjustment is more important than bulb power, as is also the quality and design of the reflector. I paid out quite a bit for genuine Hella (Cibie) flat front outer metal-and-glass units for the Dolomega and a bit less for genuine Lucas inners, Then set them up carefully on the test station beamsetter (original bowls and adjusters refurbed by me) The result is more than sufficient for use on the darkest of lanes, so far i've not even had the covers off my Square 8s, i've not needed to. I'm only running completely legal 65/55w H4s in both inner and outer lamps (with the dip not connected in the inners, again to stay within C+U regs)

There are 2 reasons why I don't look for higher output bulbs, firstly, 65/55w is the highest output that meets C+U regs, secondly, my experience with these illegal high output bulbs (ie 100/80w) has been poor, with them often failing to reach MOT focusing standard on the beamsetter. No doubt if you pay enough and get genuine Hella or similar, you might get some that actually focus correctly, my customer base is (or was) a bit more cheapskate and the "uprated" bulbs THEY bought were largely unfit for purpose!

Yes they are widely available, but if you read the (very) small print, they are for "off road use only". In much the same way that you can buy number plates indistinguishable from street legal ones but sold as "show plates" to get round the legal messing about with personal and vehicle ID consonant with buying a plate the "right" way!

Steve

_________________
'73 2 door Toledo with Vauxhall Carlton 2.0 8v engine (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine (The Dolomega)
'72 Triumph 1500FWD in Slate Grey, Now with RWD and Carledo powertrain!

Maverick Triumph, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 50 years. PM for more info or quotes.


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Sun Oct 10, 2021 9:17 pm 
Offline
TDC Shropshire Area Organiser

Joined: Sun Aug 21, 2011 5:12 pm
Posts: 7014
Location: Highley, Shropshire
Quote:
The one word of caution I would say about all this is, just because a bulb will fit doesn't mean it is compatible with the headlight unit. The problem with fitting a more powerful and different type of bulb to one the unit is designed for is, the possibility of dazzling other drivers. You see this with illegal and dangerous HID conversions.

Whether that would be an issue with the Dolly headlights, I have no idea. I don't know how much difference there is between a tungsten and halogen bulb and whether the extra output would a problem for the units reflectors.
In this case, it's not a problem, so long as you use decent quality bulbs, it will pass MOT without question.

I agree about the HID conversions and am pleased that LED headlight bulbs have now also been outlawed on "our" cars. They are a menace to other road users!

_________________
'73 2 door Toledo with Vauxhall Carlton 2.0 8v engine (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine (The Dolomega)
'72 Triumph 1500FWD in Slate Grey, Now with RWD and Carledo powertrain!

Maverick Triumph, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 50 years. PM for more info or quotes.


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Tue Oct 12, 2021 7:22 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!

Joined: Tue May 06, 2014 4:38 pm
Posts: 535
Location: South Benfleet, Essex
So far as pre-1986 Triumph Toledos & Dolomites are concerned, H4 quartz-halogen bulbs are legal, provided neither the dipped-beam or main-beam filaments of any individual bulb are NOT LESS than 30W each and the lamps DO NOT cause undue dazzle to other road users, which is principally a matter of correct headlamp alignment. This was something I clarified in late-1984, with the RAC Legal Deparment, the Department of Transport and the Essex Police Traffic Division; which you can check for yourselves in "The Road Vehicles Lighting Regulations, 1989" and Amendments.

On a "four-headlamp" Dolomite, one may legally have four main-beams and four dipped-beams! :D

https://www.legislation.gov.uk/uksi/198 ... tents/made

https://www.legislation.gov.uk/uksi/198 ... ule/4/made

https://www.legislation.gov.uk/uksi/198 ... ule/5/made

_________________
Regards.

Nigel A. Skeet

Independent tutor of mathematics, physics, technology & engineering, for secondary, tertiary, further & higher education.

https://www.linkedin.com/profile/view?id=308177758

Upgraded 1974 Triumph Toledo 1300 (Toledo / Dolomite HL / Sprint hybrid)

Onetime member + magazine editor & technical editor of Volkswagen Type 2 Owners' Club


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Wed Oct 13, 2021 5:30 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Thu Oct 06, 2011 1:13 am
Posts: 3173
Location: The continent
Quote:
I've not lately seen any of the higher wattage 410 substitute Halogen conversion bulbs being offered (though i've not checked widely) My local factors only stock the 65/55w version, which I regard as quite ample. In my experience, correct headlamp adjustment is more important than bulb power, as is also the quality and design of the reflector. I paid out quite a bit for genuine Hella (Cibie) flat front outer metal-and-glass units for the Dolomega and a bit less for genuine Lucas inners, Then set them up carefully on the test station beamsetter (original bowls and adjusters refurbed by me) The result is more than sufficient for use on the darkest of lanes, so far i've not even had the covers off my Square 8s, i've not needed to. I'm only running completely legal 65/55w H4s in both inner and outer lamps (with the dip not connected in the inners, again to stay within C+U regs)

There are 2 reasons why I don't look for higher output bulbs, firstly, 65/55w is the highest output that meets C+U regs, secondly, my experience with these illegal high output bulbs (ie 100/80w) has been poor, with them often failing to reach MOT focusing standard on the beamsetter. No doubt if you pay enough and get genuine Hella or similar, you might get some that actually focus correctly, my customer base is (or was) a bit more cheapskate and the "uprated" bulbs THEY bought were largely unfit for purpose!

Yes they are widely available, but if you read the (very) small print, they are for "off road use only". In much the same way that you can buy number plates indistinguishable from street legal ones but sold as "show plates" to get round the legal messing about with personal and vehicle ID consonant with buying a plate the "right" way!

Steve
There are good ones available here. Most oldies do want a bright lights with their new wiring harness but most of the time not changing the headlamp units.

https://www.lampengrossier.nl/epages/61 ... n/H4__P45T

No troubles with blurry lines on the test screen. You could use the 100/55w to be legal.

Jeroen

_________________
Classic Kabelboom Company. For all your wiring needs. http://www.classickabelboomcompany.com


Top
   
 Post subject: Re: 1300 Halogen Bulbs
PostPosted: Thu Oct 14, 2021 1:24 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!

Joined: Tue May 06, 2014 4:38 pm
Posts: 535
Location: South Benfleet, Essex
Quote:
I've not lately seen any of the higher wattage 410 substitute Halogen conversion bulbs being offered (though i've not checked widely) My local factors only stock the 65/55w version, which I regard as quite ample. In my experience, correct headlamp adjustment is more important than bulb power, as is also the quality and design of the reflector. I paid out quite a bit for genuine Hella (Cibie) flat front outer metal-and-glass units for the Dolomega and a bit less for genuine Lucas inners, Then set them up carefully on the test station beamsetter (original bowls and adjusters refurbed by me) The result is more than sufficient for use on the darkest of lanes, so far i've not even had the covers off my Square 8s, i've not needed to. I'm only running completely legal 65/55w H4s in both inner and outer lamps (with the dip not connected in the inners, again to stay within C+U regs)

There are 2 reasons why I don't look for higher output bulbs, firstly, 65/55w is the highest output that meets C+U regs, secondly, my experience with these illegal high output bulbs (ie 100/80w) has been poor, with them often failing to reach MOT focusing standard on the beamsetter. No doubt if you pay enough and get genuine Hella or similar, you might get some that actually focus correctly, my customer base is (or was) a bit more cheapskate and the "uprated" bulbs THEY bought were largely unfit for purpose!

Yes they are widely available, but if you read the (very) small print, they are for "off road use only". In much the same way that you can buy number plates indistinguishable from street legal ones but sold as "show plates" to get round the legal messing about with personal and vehicle ID consonant with buying a plate the "right" way!

Steve
The H4 quartz-halogen bulbs described as for "off road only" have this restriction applied to 1st April 1986 onward cars. It does not apply to our pre-April 1986 cars like my 1973 model-year VW Type 2 (first-registered November 1972) or 1974 Triumph Toledo 1300 (first registered November 1974).

On my 1973 VW Type 2, equipped with its original Hella headlamps designed for 410, 45/40W glass envelope bulbs, I never had any problem with beam alignment (as viewed on the beam-setter screen), for either the Lucas branded P45t flanged 60/55W quartz-halogen bulbs (bought in 1976 for circa £9 per pair) or the Ring branded P45t flanged 100/80W quartz-halogen bulbs (bought in circa 1988/89 for circa £6.50 each).

It's interesting to note the current availability of the following P45t flanged H4 quartz-halogen bulbs:

https://www.lampengrossier.nl/epages/61 ... 5012061545

https://www.lampengrossier.nl/epages/61 ... 5012061845

https://www.lampengrossier.nl/epages/61 ... 5012061945

https://www.lampengrossier.nl/epages/61 ... 0120613945

There is even greater scope with the P43t flanged H4 quartz-halogen bulbs:

https://www.lampengrossier.nl/epages/61 ... n/H4__P43T

Here are a few links to 45t flange to P43t flange adapters, but it pays to shop around if you want some:

https://www.candlepowerforums.com/threa ... ns.433650/

https://www.bing.com/images/search?q=p4 ... RE&first=1

https://www.classiccarleds.co.uk/produc ... lb-adapter

https://www.ebay.co.uk/itm/282431057343

www.volvosolutions.com/Misc_P45T.html

_________________
Regards.

Nigel A. Skeet

Independent tutor of mathematics, physics, technology & engineering, for secondary, tertiary, further & higher education.

https://www.linkedin.com/profile/view?id=308177758

Upgraded 1974 Triumph Toledo 1300 (Toledo / Dolomite HL / Sprint hybrid)

Onetime member + magazine editor & technical editor of Volkswagen Type 2 Owners' Club


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 12 posts ] 

All times are UTC


Who is online

Users browsing this forum: Bing, Google and 22 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited