The Triumph Dolomite Club - Discussion Forum

The Number One Club for owners of Triumph's range of small saloons from the 1960s and 1970s.
It is currently Thu Mar 28, 2024 5:47 pm

All times are UTC




Post new topic  Reply to topic  [ 34 posts ]  Go to page Previous 1 2 3 Next
Author Message
PostPosted: Mon Jan 24, 2022 11:40 am 
Offline
TDC Member

Joined: Fri Sep 11, 2015 12:02 pm
Posts: 350
Quote:
Quote:

You mean the lower ball joint mount? Are these known for flexing or breaking? I’ll definitely consider it.

And I’d more than likely copy it so it’s a drop in part. I have looked at the triumph suspension to find out camber curves and caster angles but haven’t looked at bump steer yet as I haven’t had the time to model up the steering rack and subframe fully yet, I just have a half-ok representation of the suspension mounts and arms.

And this would be a direct replacement for the stock triumph upright. Which can be used with the Sprintspeed stub axles to use a Ford Escort RS hub, either alloy or iron. And I’d never heard of a larger bearing stub axle available for the Dolomite till someone here mentioned it so if the GT6 one works, I’d go with their knowledge and judgement. And seeing as the ST parts for the triumph seems to be just parts off other triumphs, I’d guess that it’s likely that the better hub axles would be GT6
Yes I meant the Lower Ball Joint/Steering arm.
I haven’t heard of any breaking.

It just looks like you need more support around these points.

Billet alloy would be the best and strongest to machine from but not the cheapest.
Are you machining the final part.
Depends on need I guess. If more people wanted them, can look around and price up billets but for prototypes and for a one off, I was going with a fabricated design so only a few small pieces would be machined, such as the centre taper bore and the upper ball joint taper as getting them knocked out on a lathe would be much cheaper/easier than getting the full thing milled.

And to be honest, the strength difference between them, all other things being equal, would be marginal. If you wanted the lightest possible uprights which had only as much strength as necessary, billet would be the way to go, but that would cost a good bit compared to a fabricated set which should work to the same strength as factory.

And as this is all for weight saving anyway, I’m trying to take as much out anyway, such as making the uprights handed so the disc shield mounts aren’t the same strength as the brake callipers mounts.

As much as I’m in awe of the engineering that went into the dolomites suspension, from a design-vs-cost standpoint, it’s left a whole football field sized area for improvements on the table. Things like:
  • the uprights aren’t handed so you only need one tooling
  • the 3-piece upper arms so you only need 2 sets of tooling
  • make 4-5 different cars using the same basic structural design for 15 years but allows for RWD, FWD, AND AWD
And that’s my end goal for my car at least, find where the bean-counters prevented development and go as far as I can without resorting to remortgages or making a Dolomite not a Dolomite anymore. Kind of like the Alfaholics GTA 290, but I’m skipping on trying the engine side haha

_________________
So many ideas... So little budget... So little time.


Top
   
PostPosted: Mon Jan 24, 2022 7:01 pm 
Offline
TDC Member

Joined: Mon Dec 12, 2016 9:53 pm
Posts: 1699
Location: Harrow Middlesex
Quote:
Your going to need to beef up the steering arm mounting points.
I know is only a drawing at this stage it is in need of much more strengthening.

Providing you copy the original mounting points and location of the original vertical upright.
There shouldn’t be any issues with bump steer ETC unless Triumph got it wrong to start with.


Large stub axle.
What are you guys using and from where.
Are these for Escort or Triumph hubs.

Image



Image

My hubs and stub axle come from CDD Classic Driving Development mine are for a Stag,but Sprint Speed also sell the allyo hub for the Dolomite


Top
   
PostPosted: Mon Jan 24, 2022 7:47 pm 
Offline
TDC Member

Joined: Fri Sep 11, 2015 12:02 pm
Posts: 350
Quote:
Quote:
Your going to need to beef up the steering arm mounting points.
I know is only a drawing at this stage it is in need of much more strengthening.

Providing you copy the original mounting points and location of the original vertical upright.
There shouldn’t be any issues with bump steer ETC unless Triumph got it wrong to start with.


Large stub axle.
What are you guys using and from where.
Are these for Escort or Triumph hubs.

Image



Image

My hubs and stub axle come from CDD Classic Driving Development mine are for a Stag,but Sprint Speed also sell the allyo hub for the Dolomite
Ahh, fair enough, I did think they might use Stag/T2000 as I think the ST lower arms are T2000 as well.

And Sprintspeed sell an alloy rear hub which also changes the PCD to Ford pattern, and their alloy front hubs is just a stub axle which lets you use the Ford Escort alloy hubs

_________________
So many ideas... So little budget... So little time.


Top
   
PostPosted: Mon Jan 24, 2022 8:12 pm 
Offline
TDC Member
User avatar

Joined: Wed Oct 04, 2006 9:49 pm
Posts: 960
Location: Sutton,Surrey.
I’m already using the Stag Spindles.

May be a worth wilde upgrade once she’s up and running and done a few miles.

_________________
2009 Mini Clubman Cooper S Daily Driver.
1980 Dolomite Sprint with a touch of BLTS
Balanced Lightened and Tweaked 13B Rotary and SuperCharged.
Back in my possession 22 September 2019.
Rebuilding the Sprint time taken so far, 111Hrs@15/12/2020
212Hrs @31/12/2021
352 @ 28/11/2022
455Hrs @ 20/10/2023
480Hrs @ 14/03/2024
This is time taken at the Sprint not necessary time worked.

Working on a ratio of just 7Hrs a day not including driving to the Sprint.
That equals to 68 days that doesn’t include weekends.
Member TDC no 0471

Project 13B Sprint now back on.


Top
   
PostPosted: Mon Jan 24, 2022 9:01 pm 
Offline
TDC Shropshire Area Organiser

Joined: Sun Aug 21, 2011 5:12 pm
Posts: 7013
Location: Highley, Shropshire
The GT6 wheel bearings are the same part numbers as the Dolomite ones, so I doubt the GT6 stub axle is much different.

The uprated stub axle allows for 2 identical larger bearings to be fitted (note in pics the uprated stub is parallel sided and the stock one is tapered) the tiny outer bearing on the stock Dolomite stub is a known weakness for "heavy duty" use.

I wouldn't use an alloy vertical link if I could get one. I just don't think it would be strong enough unless you added a lot of extra mass to it. Which would negate the purpose of making it lighter. TBH, I also wouldn't want to trust my neck to a home made version of such a safety critical item! Especially when the standard steel one is good enough. I also don't think the original is that heavy, I strongly doubt it's over 2kg (link and stub together, but without hub and bearings) I've got a few around here, i'll weigh one tomorrow on SWMBO's kitchen scales!

It takes me around 30 secs to chop an "ear" off a stock link for TJs, where's the problem?

Steve

_________________
'73 2 door Toledo with Vauxhall Carlton 2.0 8v engine (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine (The Dolomega)
'72 Triumph 1500FWD in Slate Grey, Now with RWD and Carledo powertrain!

Maverick Triumph, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 50 years. PM for more info or quotes.


Top
   
PostPosted: Mon Jan 24, 2022 9:07 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Mon Jun 03, 2013 5:48 pm
Posts: 1635
Quote:

I wouldn't use an alloy vertical link if I could get one. I just don't think it would be strong enough unless you added a lot of extra mass to it. Which would negate the purpose of making it lighter. TBH, I also wouldn't want to trust my neck to a home made version of such a safety critical item! Especially when the standard steel one is good enough.
Steve
My thoughts too its just not worth the risk, worse case would be appearing in court to explain the death of another person because you wanted to save 1kg in weight

_________________
Some people are like Slinky's, they serve no real purpose in life but bring a smile to your face when you push them down the stairs.


Top
   
PostPosted: Mon Jan 24, 2022 9:26 pm 
Offline
TDC Member

Joined: Mon Dec 12, 2016 9:53 pm
Posts: 1699
Location: Harrow Middlesex
Quote:
The GT6 wheel bearings are the same part numbers as the Dolomite ones, so I doubt the GT6 stub axle is much different.

The uprated stub axle allows for 2 identical larger bearings to be fitted (note in pics the uprated stub is parallel sided and the stock one is tapered) the tiny outer bearing on the stock Dolomite stub is a known weakness for "heavy duty" use.

I wouldn't use an alloy vertical link if I could get one. I just don't think it would be strong enough unless you added a lot of extra mass to it. Which would negate the purpose of making it lighter. TBH, I also wouldn't want to trust my neck to a home made version of such a safety critical item! Especially when the standard steel one is good enough. I also don't think the original is that heavy, I strongly doubt it's over 2kg (link and stub together, but without hub and bearings) I've got a few around here, i'll weigh one tomorrow on SWMBO's kitchen scales!

It takes me around 30 secs to chop an "ear" off a stock link for TJs, where's the problem?

Steve
You can cut the ear of the stock link, and pick up a new mounting point for the Disc back plate from the TJ mounting brackets,but you will need to make new disc back plates ive got a template from the one i made


Top
   
PostPosted: Mon Jan 24, 2022 9:43 pm 
Offline
TDC Shropshire Area Organiser

Joined: Sun Aug 21, 2011 5:12 pm
Posts: 7013
Location: Highley, Shropshire
Quote:
Quote:
The GT6 wheel bearings are the same part numbers as the Dolomite ones, so I doubt the GT6 stub axle is much different.

The uprated stub axle allows for 2 identical larger bearings to be fitted (note in pics the uprated stub is parallel sided and the stock one is tapered) the tiny outer bearing on the stock Dolomite stub is a known weakness for "heavy duty" use.

I wouldn't use an alloy vertical link if I could get one. I just don't think it would be strong enough unless you added a lot of extra mass to it. Which would negate the purpose of making it lighter. TBH, I also wouldn't want to trust my neck to a home made version of such a safety critical item! Especially when the standard steel one is good enough. I also don't think the original is that heavy, I strongly doubt it's over 2kg (link and stub together, but without hub and bearings) I've got a few around here, i'll weigh one tomorrow on SWMBO's kitchen scales!

It takes me around 30 secs to chop an "ear" off a stock link for TJs, where's the problem?

Steve
You can cut the ear of the stock link, and pick up a new mounting point for the Disc back plate from the TJ mounting brackets,but you will need to make new disc back plates ive got a template from the one i made
I just run without backplates, had no issues so far in more than 10 years. Though I do keep the little bottom one to heatshield the balljoint, just bend it a bit!

Steve

_________________
'73 2 door Toledo with Vauxhall Carlton 2.0 8v engine (The Carledo)
'78 Sprint Auto with Vauxhall Omega 2.2 16v engine (The Dolomega)
'72 Triumph 1500FWD in Slate Grey, Now with RWD and Carledo powertrain!

Maverick Triumph, Servicing, Repairs, Electrical, Recomissioning, MOT prep, Trackerjack brake fitting service.
Apprentice served Triumph Specialist for 50 years. PM for more info or quotes.


Top
   
PostPosted: Mon Jan 24, 2022 10:23 pm 
Offline
TDC Member
User avatar

Joined: Wed Oct 04, 2006 9:49 pm
Posts: 960
Location: Sutton,Surrey.
2.5KG Vertical upright with Stag spindle and a few bolts.




Image

_________________
2009 Mini Clubman Cooper S Daily Driver.
1980 Dolomite Sprint with a touch of BLTS
Balanced Lightened and Tweaked 13B Rotary and SuperCharged.
Back in my possession 22 September 2019.
Rebuilding the Sprint time taken so far, 111Hrs@15/12/2020
212Hrs @31/12/2021
352 @ 28/11/2022
455Hrs @ 20/10/2023
480Hrs @ 14/03/2024
This is time taken at the Sprint not necessary time worked.

Working on a ratio of just 7Hrs a day not including driving to the Sprint.
That equals to 68 days that doesn’t include weekends.
Member TDC no 0471

Project 13B Sprint now back on.


Top
   
PostPosted: Mon Jan 24, 2022 11:11 pm 
Offline
TDC West Mids Area Organiser
User avatar

Joined: Thu Sep 28, 2006 1:13 pm
Posts: 13316
Location: Over here...can't you see me?
Quote:
2.5KG Vertical upright with Stag spindle and a few bolts.




Image
I take it Mrs Reader was out this evening! :lol:


Top
   
PostPosted: Mon Jan 24, 2022 11:12 pm 
Offline
TDC West Mids Area Organiser
User avatar

Joined: Thu Sep 28, 2006 1:13 pm
Posts: 13316
Location: Over here...can't you see me?
Quote:
Quote:

I wouldn't use an alloy vertical link if I could get one. I just don't think it would be strong enough unless you added a lot of extra mass to it. Which would negate the purpose of making it lighter. TBH, I also wouldn't want to trust my neck to a home made version of such a safety critical item! Especially when the standard steel one is good enough.
Steve
My thoughts too its just not worth the risk, worse case would be appearing in court to explain the death of another person because you wanted to save 1kg in weight
That was my opening response!


Top
   
PostPosted: Mon Jan 24, 2022 11:13 pm 
Offline
TDC West Mids Area Organiser
User avatar

Joined: Thu Sep 28, 2006 1:13 pm
Posts: 13316
Location: Over here...can't you see me?
Quote:
The GT6 wheel bearings are the same part numbers as the Dolomite ones, so I doubt the GT6 stub axle is much different.
I recall something in the back of my mind that they're similar, but longer...


Top
   
PostPosted: Tue Jan 25, 2022 3:10 am 
Offline
TDC Member
User avatar

Joined: Wed Oct 04, 2006 9:49 pm
Posts: 960
Location: Sutton,Surrey.
Quote:
Quote:
The GT6 wheel bearings are the same part numbers as the Dolomite ones, so I doubt the GT6 stub axle is much different.
I recall something in the back of my mind that they're similar, but longer...
Stag spindles are slightly longer.

Mrs R was at home this evening,
Good job as this was done earlier in the day. 😂

_________________
2009 Mini Clubman Cooper S Daily Driver.
1980 Dolomite Sprint with a touch of BLTS
Balanced Lightened and Tweaked 13B Rotary and SuperCharged.
Back in my possession 22 September 2019.
Rebuilding the Sprint time taken so far, 111Hrs@15/12/2020
212Hrs @31/12/2021
352 @ 28/11/2022
455Hrs @ 20/10/2023
480Hrs @ 14/03/2024
This is time taken at the Sprint not necessary time worked.

Working on a ratio of just 7Hrs a day not including driving to the Sprint.
That equals to 68 days that doesn’t include weekends.
Member TDC no 0471

Project 13B Sprint now back on.


Top
   
PostPosted: Sat Jan 29, 2022 7:55 pm 
Offline
TDC Member

Joined: Fri Sep 11, 2015 12:02 pm
Posts: 350
Quote:
The GT6 wheel bearings are the same part numbers as the Dolomite ones, so I doubt the GT6 stub axle is much different.

The uprated stub axle allows for 2 identical larger bearings to be fitted (note in pics the uprated stub is parallel sided and the stock one is tapered) the tiny outer bearing on the stock Dolomite stub is a known weakness for "heavy duty" use.

I wouldn't use an alloy vertical link if I could get one. I just don't think it would be strong enough unless you added a lot of extra mass to it. Which would negate the purpose of making it lighter. TBH, I also wouldn't want to trust my neck to a home made version of such a safety critical item! Especially when the standard steel one is good enough. I also don't think the original is that heavy, I strongly doubt it's over 2kg (link and stub together, but without hub and bearings) I've got a few around here, i'll weigh one tomorrow on SWMBO's kitchen scales!

It takes me around 30 secs to chop an "ear" off a stock link for TJs, where's the problem?

Steve
Well, aluminium is 1/2 the weight, 2/3 the strength, so you need 4/3rds the thickness for equivalent strength, which works out about a 1/3 weight loss everything being equal.

And yes, that’s why I’d never consider selling them or anything, I don’t want that liability hanging over my head, where as I’m more than happy to make my own set and put myself at risk. These would pretty much be a track only part, as I doubt it would benefit anyone off track.

_________________
So many ideas... So little budget... So little time.


Top
   
PostPosted: Mon Jan 31, 2022 4:07 am 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Mon Jun 03, 2013 5:48 pm
Posts: 1635
Quote:


Well, aluminium is 1/2 the weight, 2/3 the strength, so you need 4/3rds the thickness for equivalent strength, which works out about a 1/3 weight loss everything being equal.

Making it thicker doesn't always mean you are making it stronger.

_________________
Some people are like Slinky's, they serve no real purpose in life but bring a smile to your face when you push them down the stairs.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 34 posts ]  Go to page Previous 1 2 3 Next

All times are UTC


Who is online

Users browsing this forum: Bing, Google and 34 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited