The Triumph Dolomite Club - Discussion Forum

The Number One Club for owners of Triumph's range of small saloons from the 1960s and 1970s.
It is currently Fri Mar 29, 2024 5:40 am

All times are UTC




Post new topic  Reply to topic  [ 6 posts ] 
Author Message
 Post subject: Paint or Power Coat
PostPosted: Thu Jan 20, 2022 5:45 pm 
Offline
TDC Member

Joined: Wed Jun 30, 2021 3:47 pm
Posts: 67
Location: USA
My recently acquired Sprint came without an original airbox. Xvivalve provide a replacement along with a host of other spares.

I had read that power coating is more durable and flexible than paint so I decide to have a go a power coating using a cheap gun from Eastwood (US company).

It turned out really nice but the coating is actually more brittle than paint and has a tendency to chip. Once chipped its harder to touch up than paint. I may have applied the coating too thickly.

I have coated some other items, a wheel, brake peddle and clutch brackets which turned out great.

My experience so far is something like an airbox is better painted.


Attachments:
air box 2.jpg
air box 2.jpg [ 73.14 KiB | Viewed 227 times ]
Air box 1.jpg
Air box 1.jpg [ 103.23 KiB | Viewed 227 times ]
Top
   
 Post subject: Re: Paint or Power Coat
PostPosted: Thu Jan 20, 2022 8:15 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!

Joined: Mon Dec 03, 2012 6:04 pm
Posts: 1549
How did you prep and cure your powder coated parts? That will have a big impact on the quality and durability of your finish.


Top
   
 Post subject: Re: Paint or Power Coat
PostPosted: Thu Jan 20, 2022 9:14 pm 
Offline
TDC Member

Joined: Mon Dec 12, 2016 9:53 pm
Posts: 1699
Location: Harrow Middlesex
Ive got one of those Eastwood powder coating kits,not got round to using mine yet

Dave


Top
   
 Post subject: Re: Paint or Power Coat
PostPosted: Thu Jan 20, 2022 10:05 pm 
Offline
Future Club member hopefully!
Future Club member hopefully!
User avatar

Joined: Mon Jun 03, 2013 5:48 pm
Posts: 1635
if its chipping that easily it either not prepped correctly, not coated fully or not cured right.

How are you prepping and cleaning.
What static device do you use and
how are you 'cooking' the parts?

I have a powdercoating set up from
https://www.electrostaticmagic.co.uk

I always sandblast and clean using a paint prep cleaner first and have dropped and 'scratched' a few parts i have done and they have survived

_________________
Some people are like Slinky's, they serve no real purpose in life but bring a smile to your face when you push them down the stairs.


Top
   
 Post subject: Re: Paint or Power Coat
PostPosted: Thu Jan 20, 2022 10:57 pm 
Offline
TDC West Mids Area Organiser
User avatar

Joined: Thu Sep 28, 2006 1:13 pm
Posts: 13317
Location: Over here...can't you see me?
It still looks a lot better than when it was in my possession!


Top
   
 Post subject: Re: Paint or Power Coat
PostPosted: Fri Jan 21, 2022 4:55 pm 
Offline
TDC Member

Joined: Wed Jun 30, 2021 3:47 pm
Posts: 67
Location: USA
I wouldn't say that the coating chipped easily. The clip in the photo is welded on at a slight angle which means you need a lot of force to close it. The clip is also quite sharp. This combination chipped the coating where the clip grips the airbox. Then when unclipping the same dynamics cause the clip to hit the airbox with a lot of force. I expect that paint would also be damaged but maybe more of a scratch than a chip. And easier to touch up.

I prepared the piece the same as I would for paint. Removed most of the paint with a wire wheel. Soda blasted hard to reach areas, Sanded with 120, cleaned with painting prep.

Then coated and cured at 420F for 20 mins. I definitely did apply the powder a bit to thickly in some places, especially between some of the folds of the sheet metal.

This is my set up. A bit Heath Robinson but does the job. I also set up a double oven in the garage that somebody was throwing away.

All in all I have been pleased with the results and would recommend this gun.


Attachments:
powder coat.jpg
powder coat.jpg [ 102.32 KiB | Viewed 126 times ]
powder gun.jpg
powder gun.jpg [ 121.31 KiB | Viewed 126 times ]
Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 6 posts ] 

All times are UTC


Who is online

Users browsing this forum: Google and 25 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited