Triumph 1500TC Now A Rolling Resto :-) Most Photo's Restored :-)

Restoring your car? Tell us about it here!
Message
Author
User avatar
DazasDolly
Guest contributor
Guest contributor
Posts: 1162
Joined: Sun Mar 14, 2010 7:44 pm
Location: Colchester, ESSEX

Re: Restoration Triumph 1500TC

#46 Post by DazasDolly »

Thanks Phil will give it a try :P

Regards

Daz
1974 Triumph 1500TC In Maple Brown, (MABLE) GGN 647N
1968 Triumph Vitesse Saloon 2L MK2 Not for the faint hearted, mega restoration
1973 Triumph Spitfire In Mimosa
User avatar
Jod Clark
Guest contributor
Guest contributor
Posts: 2567
Joined: Tue Oct 03, 2006 7:38 pm
Location: Birmingham

Re: Restoration Triumph 1500TC

#47 Post by Jod Clark »

Cleaning your pistons with a powered wire brush is a turd of an idea. Turn the engine so they're all halfway down their bores, add some paraffin and let it have a soak for a day or two, then bring the pistons up the bores and wipe the carbon away. This technique will also help to free-off any sticky piston rings.

No stem seals to worry about in the Triumph OHV engine.
Vindicator Sprint, Honda Fireblade RRX 919cc, re-powered by AB Performance. Quick.
Phil_G

Re: Restoration Triumph 1500TC

#48 Post by Phil_G »

Jod Clark wrote:Cleaning your pistons with a powered wire brush is a turd of an idea. Turn the engine so they're all halfway down their bores, add some paraffin and let it have a soak for a day or two, then bring the pistons up the bores and wipe the carbon away. This technique will also help to free-off any sticky piston rings.

No stem seals to worry about in the Triumph OHV engine.


So i wasn't too far off the mark then? :shock: .
User avatar
Toledo Man
Guest contributor
Guest contributor
Posts: 7542
Joined: Tue Oct 03, 2006 5:52 pm
Location: Halifax, West Yorkshire
Contact:

Re: Restoration Triumph 1500TC

#49 Post by Toledo Man »

Jod, I bow to your superior knowledge...
Toledo Man

West Yorkshire Area Organiser
Meetings take place on the first Wednesday of the month at 8.00pm at The Railway, 1 Birstall Lane, Drighlington, Bradford, BD11 1JJ

2003 Volvo XC90 D5 SE (PX53 OVZ - The daily driver)
2009 Mercedes-Benz W204 C200 CDI Sport (BJ58 NCV - The 2nd car)
1991 Toyota Celica GT (J481 ONB - a project car)
Former stable of SAY 414M (1974 Toledo), GRH 244D (1966 1300fwd), CDB 324L (1973 1500fwd), GGN 573J (1971 1500fwd), DCP 625S (1977 Dolomite 1300) & LCG 367N (1975 Dolomite Sprint), NYE 751L (1972 Dolomite 1850 auto) plus 5 Acclaims and that's just the Triumphs!

Check my blog at http://triumphtoledo.blogspot.com
My YouTube Channel with a bit of Dolomite content.

"There is only one way to avoid criticsm: Do nothing, say nothing and BE nothing." Aristotle
User avatar
DazasDolly
Guest contributor
Guest contributor
Posts: 1162
Joined: Sun Mar 14, 2010 7:44 pm
Location: Colchester, ESSEX

Re: Restoration Triumph 1500TC

#50 Post by DazasDolly »

Hi guys

Just thought I would let you know I will be rebuilding the engine tomorrow, The head gasket set was delivered yesterday and I have been out and bought the compound for grinding the valves down, also a new oil filter will be applied and new oil once the cylinder head is back on with the rocker cover.

is there anything I should do before I try and start her up once she is put back together.

Hopefully all will be good.

Kind Regards

Daz
1974 Triumph 1500TC In Maple Brown, (MABLE) GGN 647N
1968 Triumph Vitesse Saloon 2L MK2 Not for the faint hearted, mega restoration
1973 Triumph Spitfire In Mimosa
Spunkymonkey

Re: Restoration Triumph 1500TC

#51 Post by Spunkymonkey »

Once she's all bolted back, go round and double-check that you haven't forgotten anything (including water and oil - it's surprisingly easy to do :oops: ). Before you put the plug leads back on, and preferably with the plugs out, crank her over for a few seconds until the oil light goes out to prime the new filter. This should also give the fuel pump a good chance to refill the float chambers.

Then fit plugs and leads and flick the switch. Do not forget to re-torque the head bolts once she's been warmed up. It's generally recommended to do this while the engine is still warm on cast-iron heads but you have to remove the rocker shaft to get at some of the studs on these, and you need to set the valve clearances when cold, so that's a PITA. As long as you do re-torque them (to allow for the gasket compressing as it heats up) it's fine doing it once it's cooled down again.

When re-torquing don't just apply torque wrench and pull - you'll probably end up over-torquing some of them. The correct method is to undo each stud about 1/4 turn then re-tighten according to the normal tightening sequence (no need to slacken them all at once - slacken and immediately tighten each one in turn)
User avatar
DazasDolly
Guest contributor
Guest contributor
Posts: 1162
Joined: Sun Mar 14, 2010 7:44 pm
Location: Colchester, ESSEX

Re: Restoration Triumph 1500TC

#52 Post by DazasDolly »

Hi Guys

Well I put the parafin down the cylinders to help with cleaning, but the parafin kept going down into the sump.

So last weekend I bought the engine from one of my previous posts for £50, and diesel to skegness, 137 miles each way lol

so today im in the process of taking out the old engine and putting the new one in, I couldn't get the valves lapped in properly so my engineer friend from work is going to clean it up etc.

while the original engine is out, over time im going to rebuild the bottom end, and have basically a recon engine.

Hopefully once welding is done I will run the car on the engine I have bought, until the original engine is ready to go in.

Just thought I would give an update.

Regards

Daz
1974 Triumph 1500TC In Maple Brown, (MABLE) GGN 647N
1968 Triumph Vitesse Saloon 2L MK2 Not for the faint hearted, mega restoration
1973 Triumph Spitfire In Mimosa
User avatar
DazasDolly
Guest contributor
Guest contributor
Posts: 1162
Joined: Sun Mar 14, 2010 7:44 pm
Location: Colchester, ESSEX

Re: Restoration Triumph 1500TC

#53 Post by DazasDolly »

Hi guys

Its been a while, thought i would come and give you a quick update.

All is going well, the old engine is dead, there was a nasty crack in the cylinder head, and after removing the sump, there was lots of play.

Im ready to start welding, just waiting for the mig from work.

just need to buy the sills.

Also need to buy, front and rear windscreen rubber seals.

The engine we bought from ebay for £50, runs ok, took a while to get it there, but had a prob with fuel getting up. So may fit an electric pump when the engine goes back in.

Regards

Daz
1974 Triumph 1500TC In Maple Brown, (MABLE) GGN 647N
1968 Triumph Vitesse Saloon 2L MK2 Not for the faint hearted, mega restoration
1973 Triumph Spitfire In Mimosa
User avatar
DazasDolly
Guest contributor
Guest contributor
Posts: 1162
Joined: Sun Mar 14, 2010 7:44 pm
Location: Colchester, ESSEX

Re: Restoration Triumph 1500TC

#54 Post by DazasDolly »

Hi Guys

I thought I would download some pics, to show you the progress that im slowly making.

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Ready for welding, just waiting for the mig to come from my mates.

regards

Darren
Last edited by DazasDolly on Sun Feb 04, 2018 9:18 pm, edited 1 time in total.
1974 Triumph 1500TC In Maple Brown, (MABLE) GGN 647N
1968 Triumph Vitesse Saloon 2L MK2 Not for the faint hearted, mega restoration
1973 Triumph Spitfire In Mimosa
JPB

Re: Restoration Triumph 1500TC

#55 Post by JPB »

Brilliant stuff. This car probably wouldn't have survived without your kind of determination, keep the updates coming please.

:thumbsup: :thumbsup:
User avatar
DazasDolly
Guest contributor
Guest contributor
Posts: 1162
Joined: Sun Mar 14, 2010 7:44 pm
Location: Colchester, ESSEX

Re: Restoration Triumph 1500TC

#56 Post by DazasDolly »

Thanks for kind words John.

It has been hard work, especially on these hot summer days we are having at the mo.

Also the colour isn't Sienna brown like I thought, its Maple, so hopefully will get a good match from paints4u. Also struggling to find Hammerite Brown to go over the stonechip once she's been welded.

I am aiming for spring 2011 to have her on the road, so fingers crossed.

Thanks Again

Darren
1974 Triumph 1500TC In Maple Brown, (MABLE) GGN 647N
1968 Triumph Vitesse Saloon 2L MK2 Not for the faint hearted, mega restoration
1973 Triumph Spitfire In Mimosa
DoloWIGHTY

Re: Restoration Triumph 1500TC

#57 Post by DoloWIGHTY »

Fingers crossed here too. Fantastic work there, cannot say how pleased I am to see a brown 1500TC receiving this amount of work and dedication. :thumbsup:
bifold

Re: Restoration Triumph 1500TC

#58 Post by bifold »

DazasDolly wrote:Thanks for kind words John.

It has been hard work, especially on these hot summer days we are having at the mo.

Also the colour isn't Sienna brown like I thought, its Maple, so hopefully will get a good match from paints4u. Also struggling to find Hammerite Brown to go over the stonechip once she's been welded.

I am aiming for spring 2011 to have her on the road, so fingers crossed.

Thanks Again

Darren
you could mix red and green Hammerite to make brown(I have a fair few tools and machines that are painted in hammerite and some makers have their own colours,so I have been mixing on a palate to do small touch ups rather than repaints,Dad was a printer and used to mix hes own inks)
User avatar
DazasDolly
Guest contributor
Guest contributor
Posts: 1162
Joined: Sun Mar 14, 2010 7:44 pm
Location: Colchester, ESSEX

Re: Restoration Triumph 1500TC

#59 Post by DazasDolly »

Not done alot this week, due to me being on a course for work, had to study.

Mig welder has finally turned up, im dreading this bit. Never used a mig in my life so its going to be a big learning curve.

Also I have now found that ronseal do a brown paint similar to hammerite, but also hammerite do a chestnut brown, so i will give them a look.

The rest of the heater is now painted, I will take some pics at the weekend and put them on, it look bloody good :P

Kind Regards

Darren
1974 Triumph 1500TC In Maple Brown, (MABLE) GGN 647N
1968 Triumph Vitesse Saloon 2L MK2 Not for the faint hearted, mega restoration
1973 Triumph Spitfire In Mimosa
User avatar
sprint95m
TDC Member
Posts: 6502
Joined: Thu Aug 09, 2007 1:22 pm
Location: Caithness, Scotland

You need...........

#60 Post by sprint95m »

Tractor paint........?
Your local agricultural supplier can supply brown paint (very close to Sienna brown) and primer too.
Cheaper and longer lasting than Hammerite.
Can be brushed or sprayed.
TDC Forum moderator
PLEASE help us to maintain a friendly forum,
either PM or use Report Post if you see anything you are unhappy with. Thanks.
Post Reply