door handle gaskets

[new to this]

I wasn't going to use gasket paper, probably neoprene or similar.

If you have anything that needs to be "CADed" Mark, give me a shout & I'll see what I can do.

Do you need a sample, ive ordered the XJ6 ones but also ordered some rubber gasket material

Dave

If you have a set you don't mind posting me, yes please.

Martin

As soon as they arive ill send you a door set

Dave

[Mad Mart]

[Sprintparts]

I wasn't going to use gasket paper, probably neoprene or similar.

If you have anything that needs to be "CADed" Mark, give me a shout & I'll see what I can do.

Thanks.

[DOLOMITE 135]

Interestingly I just checked the door handle gaskets I have (purchased from Rimmers some time ago) and the larger gasket is made from Rubber / Neoprene, whilst the smaller one is a thick card like material. The ones I recently removed from my doors were the latter material so I wonder if the larger ones are re-manufactured items or if the material used changed over time.

[new to this]

While were on about door handle gaskets,do the door locks have a gasket ?

Dave

[Mad Mart]

While were on about door handle gaskets,do the door locks have a gasket ?

Dave

I'm pretty sure they do but they don't seem to show one in my parts catalogue.

[DOLOMITE 135]

The locks do use a gasket, but as stated by Mad Mart above they do not appear in the parts catalogue.


I wonder if Jaguar XJ6/XJ12 door handle gaskets apparently fit, would their lock gaskets fit as well?

https://www.sngbarratt.com/English/#/UK ... AEU1587%60

They look very similar, but it's not possible to judge their size from a picture and thus if interchangeable.
It should be noted that the Dolomite / Toledo door locks also have three locating tabs so the fourth location tab cut out in the lock gasket shown in my photo is redundant.

[new to this]

The locks do use a gasket, but as stated by Mad Mart above they do not appear in the parts catalogue.


I wonder if Jaguar XJ6/XJ12 door handle gaskets apparently fit, would their lock gaskets fit as well?

https://www.sngbarratt.com/English/#/UK ... AEU1587%60

They look very similar, but it's not possible to judge their size from a picture and thus if interchangeable.
It should be noted that the Dolomite / Toledo door locks also have three locating tabs so the fourth location tab cut out in the lock gasket shown in my photo is redundant.

I made a door lock gasket today, the three locating tabs don't go the whole length of the lock so its easier to make the gasket just a centre whole no locating tabs to worry about

Dave

[DOLOMITE 135]

the three locating tabs don't go the whole length of the lock

Two of the tabs where the clip holds it in position in the door do not as you say go the lenght of the body of the lock, the third central one does to prevent the lock from turning in the door, so you may still need a single tab cut out to fit correctly.

[new to this]

That’s the lock fitted with gasket in place

[Mad Mart]

Thanks to Dave for sending me the door handle gaskets to use as a pattern.

I've drawn the two door handle gaskets (top) the boot lock gasket (bottom left) and the door lock gasket (bottom right).



I just need to source the material to print them on.

[new to this]

Will that mean if i ask does the club have door handle gaskets, your now be able to say yes

Dave

[Carledo]

Thanks to Dave for sending me the door handle gaskets to use as a pattern.

I've drawn the two door handle gaskets (top) the boot lock gasket (bottom left) and the door lock gasket (bottom right).



I just need to source the material to print them on.

I'll take a couple of sets when you go into production!

Steve

[Mad Mart]

Will that mean if i ask does the club have door handle gaskets, your now be able to say yes

Dave

Once we've sorted out costings, yes.