Project SFB

Message

Sprint36 · #91 Post by **Sprint36** » Wed Jan 10, 2007 8:50 am

http://www.bbc.co.uk/comedy/guide/artic ... 1975.shtml

Third paragraph, second line Adam.

Before your time but frequently repeated.

David

DoloWIGHTY · #92 Post by **DoloWIGHTY** » Wed Jan 10, 2007 9:16 am

Mart, are you going to put everything back in/on the doors before hanging, or hang them first (weigh a lot less) and then start re assembling things?

ALAN

#93 Post by **Mad Mart** » Wed Jan 10, 2007 9:46 am

I'm going to hang them first Alan. Apart from the extra weight, it's easier & a lot less likely to scratch the paint work.

DoloWIGHTY · #94 Post by **DoloWIGHTY** » Wed Jan 10, 2007 9:55 am

Thanks Mart. It confirms what I have been planning to do with mine, I think they will be easier to adjust (if needed) the only thing I feel needed to be carefull of is putting the front quarter glass in place back in.

Good luck, be interested to see how they look back on the car.

ALAN

Lee Flintoft · #95 Post by **Lee Flintoft** » Fri Jan 12, 2007 6:36 am

I learnt the hard way, took one off and chipped it getting it off. All sorted now though

, Did the others while they were on the car.

KWM338R · #96 Post by **KWM338R** » Sat Jan 13, 2007 6:42 pm

What paint are you gents using to paint your suspension and axles. What do you use to clean them before painting, will paint thinners do an ok job to clean with? I want to clean and paint the inside of the boot and the engine bay, what do you all use to clean the muck off those before painting. Its been a long time since I painted anything, used to just slap smoothrite everywhere without much thought to preparation.

cheers
Mark

Reg · #97 Post by **Reg** » Sat Jan 13, 2007 8:23 pm

Any more progress photo's chaps?

#98 Post by **Mad Mart** » Sat Jan 13, 2007 11:52 pm

Yes, we've both been busy today, pics tomorrow. Too knackered to put them up now.

Lee Flintoft · #99 Post by **Lee Flintoft** » Sun Jan 14, 2007 8:59 am

Busy day with lots of swear words...

#100 Post by **Mad Mart** » Sun Jan 14, 2007 10:04 am

SNAP!

Same here Lee, blood sweat & swear words.

It wasn't that bad actually but I do owe a big thank you to Mary (again) for helping me to manouver the engine & box under the car.

Lee Flintoft · #101 Post by **Lee Flintoft** » Mon Jan 15, 2007 6:27 am

This is getting scary, is that my jack Mart?

#102 Post by **Mad Mart** » Mon Jan 15, 2007 8:23 am

oh yea! sorry, I borrowed it when you weren't looking.

#103 Post by **Mad Mart** » Sun Feb 04, 2007 6:35 pm

Today I half fitted the S/S exhaust. Then I decided I'd rather put the carbs on.

Looked underneath the inlet manifold & there was something strange happening with the water take off nearest the bulkhead, a banjo joint!

Anyway, I whipped that out & put in the proper pipe. The stat housing looked a bit cruddy so I thought I'd whip that off & give it a clean inside & out. I'm glad I did, took the thermostat out & it was the wrong type, the one without the foot.

Then I thought I would turn the engine over by hand & set it to TDC. Took the plugs out first, bloody Champion plugs....bin. Set the timing to TDC & someone had set the dizzy 180 degs. out so the rotor arm was pointing towards the head instead of the lug on the dizzy therefore the leads in the dizzy cap are all arse backzerds. I know it'll still work like this but I like to have it right.

Lee Flintoft · #104 Post by **Lee Flintoft** » Sun Feb 04, 2007 8:01 pm

pics?

#105 Post by **Mad Mart** » Sun Feb 04, 2007 8:25 pm

Ah!, glad you said that Lee, I'd left my camera in the garage.

Engine:

Banjo joint thingy: